Acura TSX / Honda Accord CL. Manual — part 542
Fig. 11: Connecting EVAP Canister Purge Valve 2P Connector Terminal No. 2 To Body Ground
With A Jumper Wire
22. Check for continuity between ECM/PCM connector terminal B21 and body ground.
Is there continuity?
YES: Go to step 23.
NO: Repair open in the wire between the EVAP canister purge valve and the ECM/PCM
(B21), then go to step 25 .
2004 Acura TSX
2004 ENGINE PERFORMANCE EVAP System - TSX
Fig. 12: Checking For Continuity Between ECM/PCM Connector Terminal B21 & Body
Ground
23. Measure resistance between EVAP canister purge valve 2P connector terminals No. 1 and No. 2.
Is there about 33 ohm at room temperature?
YES: Go to step 31 .
NO: Go to step 24.
2004 Acura TSX
2004 ENGINE PERFORMANCE EVAP System - TSX
Fig. 13: Measuring Resistance Between EVAP Canister Purge Valve 2P Connector Terminals
No. 1 & No. 2
24. Replace the EVAP canister purge valve (see EVAP CANISTER PURGE VALVE REPLACEMENT ).
25. Reconnect ECM/PCM connector B (24P).
26. Reconnect the EVAP canister purge valve 2P connector.
27. Turn the ignition switch ON (II).
28. Reset the ECM/PCM with the HDS.
29. Do the ECM/PCM idle learn procedure (see ECM/PCM IDLE LEARN PROCEDURE ).
30. Check for Temporary DTCs or DTCs in the DTCs MENU with the HDS.
Are any Temporary DTCs or DTCs indicated?
YES: If DTC P0443 is indicated, check for poor connections or loose terminals at the EVAP
canister purge valve and the ECM/PCM, then go to step 1 . If any other Temporary DTCs or
DTCs are indicated, go to the indicated DTC troubleshooting.
NO: Troubleshooting is complete.
31. Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM (see
HOW TO SUBSTITUTE THE ECM/PCM ).
32. Check for Temporary DTCs or DTCs in the DTCs MENU with the HDS.
2004 Acura TSX
2004 ENGINE PERFORMANCE EVAP System - TSX
Are any Temporary DTCs or DTCs indicated?
YES: If DTC P0443 is indicated, check for poor connections or loose terminals at the EVAP
canister purge valve and the ECM/PCM, then go to step 1 . If any other Temporary DTCs or
DTCs are indicated, go to the indicated DTC troubleshooting.
NO: If the ECM/PCM was updated, troubleshooting is complete. If the ECM/PCM was
substituted, replace the original ECM/PCM (see HOW TO REMOVE THE ECM/PCM
FOR TESTING ).
DTC P0451: FTP SENSOR RANGE/PERFORMANCE PROBLEM
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Start the engine, and let it idle for 1 minute.
4. Monitor the OBD STATUS for DTC P0451 in the DTCs MENU with the HDS.
Does the screen indicate FAILED?
YES: Go to step 5.
NO: If the screen indicates PASSED, intermittent failure, system is OK at this time. If the
screen indicates NOT COMPLETED, go to step 3 and recheck.
5. Turn the ignition switch OFF.
6. Replace the FTP sensor (see FTP SENSOR REPLACEMENT ).
7. Turn the ignition switch ON (II).
8. Reset the ECM/PCM with the HDS.
9. Do the ECM/PCM idle learn procedure (see ECM/PCM IDLE LEARN PROCEDURE ).
10. Start the engine, and let it idle for 1 minute.
11. Check for Temporary DTCs or DTCs in the DTCs MENU with the HDS.
Are any Temporary DTCs or DTCs indicated?
YES: If DTC P0451 is indicated, check for poor connections or loose terminals at the FTP
sensor and the ECM/PCM, then go to step 1 . If any other Temporary DTCs or DTCs are
indicated, go to the indicated DTC troubleshooting.
NO: Go to step 12.
12. Monitor the OBD STATUS for DTC P0451 in the DTCs MENU with the HDS.
Does the screen indicate PASSED?
YES: Troubleshooting is complete.
NO: If the screen indicates FAILED, check for poor connections or loose terminals at the
FTP sensor and the ECM/PCM, then go to step 1 . If the screen indicates NOT
COMPLETED, go to step 10 and recheck.
DTC P0452: FTP SENSOR CIRCUIT LOW VOLTAGE
NOTE:
If DTC P2422 is stored at the same time as DTC P0451, troubleshoot DTC P2422
first, then recheck for DTC P0451.
2004 Acura TSX
2004 ENGINE PERFORMANCE EVAP System - TSX
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст