Acura TSX / Honda Accord CL. Manual — part 972
Fig. 168: Checking For Continuity Between Transmission Gear Selection Switch Connector
Terminals No. 2 & No. 3
7. Turn the ignition switch ON (II).
8. Measure the voltage between transmission gear selection switch connector terminal No. 3 and body
ground.
Is there about 5 V?
YES: Repair open in the wire between transmission gear selection switch connector terminal
No. 2 and ground (G501), or repair poor ground (G501), then go to step 10 .
NO: Go to step 9.
2004 Acura TSX
2004 AUTOMATIC TRANSMISSIONS Diagnosis - MCTA 5-Speed
Fig. 169: Measuring The Voltage Between Transmission Gear Selection Switch Connector
Terminal No. 3 & Body Ground
9. Measure the voltage between PCM connector terminal D2 and body ground.
Is there about 5 V?
YES: Repair open in the wire between PCM connector terminal D2 and the transmission
gear selection switch connector, then go to step 10.
NO: Check for loose or poor connections at PCM connector terminal D2. If the connection is
OK, update the PCM if it does not have the latest software, or substitute a known-good PCM
(see PCM UPDATING & SUBSTITUTION FOR TESTING ), then recheck. If the
symptom/indication goes away with a known-good PCM, replace the original PCM.
2004 Acura TSX
2004 AUTOMATIC TRANSMISSIONS Diagnosis - MCTA 5-Speed
Fig. 170: Measuring The Voltage Between PCM Connector Terminal D2 & Body Ground
10. Clear the DTC with the HDS.
11. Start the engine in the P position, wait for more than 10 seconds, then shift to the M position.
12. Push the shift lever toward shiftup position (+) slowly, and return to neutral position; repeat this test 10
times or more.
13. Pull the shift lever toward shiftdown position (-) slowly, and return to neutral position; repeat this test 10
times or more.
2004 Acura TSX
2004 AUTOMATIC TRANSMISSIONS Diagnosis - MCTA 5-Speed
14. Check the OBD STATUS in DTCs MENU for a pass/fail test of code P0958.
Did the result indicate a pass?
YES: The problem has been corrected.
NO: Return to step 1 and recheck.
DTC P0962: PROBLEM IN A/T CLUTCH PRESSURE CONTROL SOLENOID VALVE A CIRCUIT
1. Clear the DTC with the HDS.
2. Check that DTC P0962 recurs.
Is DTC P0962 indicated?
YES: Go to step 6 .
NO: Go to step 3.
3. Select P CTRL SOL CONTROL in MISC. TEST MENU, then select P. CONTROL SOL A in P CTRL
SOL CTRL MENU with the HDS.
4. Drive with the A/T clutch pressure control solenoid valve A at 1.0 A in SOL A CONTROL menu.
5. Check the OBD STATUS in DTCs MENU for a pass/fail test of code P0962.
Did the result indicate a fail?
YES: Go to step 6.
NO: Intermittent failure, the system is OK at this time. Check for poor connections or loose
terminals at the A/T clutch pressure control solenoid valve A and PCM. If the tester indicates
NOT COMPLETE, return to step 3 and recheck.
6. Turn the ignition switch OFF.
7. Disconnect the A/T clutch pressure control solenoid valve A connector.
8. Measure A/T clutch pressure control solenoid valve A resistance at the solenoid connector.
Is there 3-10 ohm?
YES: Go to step 9.
NO: Replace the A/T clutch pressure control solenoid valve A (see A/T CLUTCH
PRESSURE CONTROL SOLENOID VALVE A REPLACEMENT ), then go to step
12 .
NOTE:
z
Record all freeze data and review General Troubleshooting Information
(see GENERAL TROUBLESHOOTING INFORMATION ) before you
troubleshoot.
z
This code is caused by an electrical circuit problem and cannot be caused
by a mechanical problem in the transmission.
2004 Acura TSX
2004 AUTOMATIC TRANSMISSIONS Diagnosis - MCTA 5-Speed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст