Acura TSX / Honda Accord CL. Manual — part 773
Fig. 3: Adjusting Rear Toe-In (Typical)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
TURNING ANGLE INSPECTION
Turn the steering wheel fully to the right and left while applying the brake, and check the turning angles of both
front wheels. See WHEEL ALIGNMENT SPECIFICATIONS . If the turning angle is not within the
specification or the inward turning angles differ between the right and left side, check for bent or damaged
suspension components.
RIDING HEIGHT ADJUSTMENT
TORQUE SPECIFICATIONS
NOTE:
Riding height specification is not available from manufacturer. Ensure riding
height between left and right side of vehicle does not differ by more than 1" (25
mm).
2004 Acura TSX
2004 WHEEL ALIGNMENT Specifications & Procedures - TSX
TORQUE SPECIFICATIONS
WHEEL ALIGNMENT SPECIFICATIONS
WHEEL ALIGNMENT SPECIFICATIONS
Application
Ft. Lbs. (N.m)
Rear Control Arm Self-Locking Nut
40 (54)
Spindle Nut
181 (245)
Tie Rod Lock Nut
33 (44)
Wheel Lug Nut
80 (108)
Application
Preferred
Range
Camber
(1)
Front
0
-.75 To .75
Rear
-1
-1.5 To -.5
Caster
(1)
Front
3.22
2.47 To 3.97
Toe-In
(2)
Front
0
-.08 To .08 (-2 To 2)
Rear
.08 (2)
0 To .16 (0 To 4)
Toe-Out On Turns
(1)
Inner
35.25
N/A
Outer
29.63
N/A
Turning Angle
(1)
Inward Wheel
35.25
33.25 To 37.25
Outward Wheel (Reference)
29.63
N/A
(1)
Measurements are in degrees.
(2)
Measurements are in inches (mm).
2004 Acura TSX
2004 WHEEL ALIGNMENT Specifications & Procedures - TSX
2004 AUTOMATIC TRANSMISSIONS
A/T Overhaul (MCTA) - TSX
TRANSMISSION END COVER
END COVER REMOVAL
Special Tools Required
Mainshaft holder 07GAB-PF50101 or 07GAB-PF50100
1. Remove the two bolts securing the ATF cooler inlet line brackets, ATF filter bracket bolt, line bolt, and
remove the ATF cooler line/ATF filter (D) and filter brackets (E).
Fig. 1: Removing The Two Bolts Securing The ATF Cooler Inlet Line Brackets, ATF Filter Bracket
Bolt, Line Bolt, & Removing The ATF Cooler Line/ATF Filter And Filter Brackets
2004 Acura TSX
2004 AUTOMATIC TRANSMISSIONS A/T Overhaul (MCTA) - TSX
2004 Acura TSX
2004 AUTOMATIC TRANSMISSIONS A/T Overhaul (MCTA) - TSX
2. Remove the ATF cooler outlet line (F).
3. Remove the dipstick guide pipe (G).
4. Remove the A/T clutch pressure control solenoid valve A, ATF joint pipes, ATF pipe, and gasket.
5. Remove the A/T clutch pressure control solenoid valves B and C, ATF joint pipes, and gasket.
6. Remove the transmission range switch cover (H).
7. Remove the transmission range switch harness clamps (I) from the clamp bracket (J), then remove the
transmission range switch (K).
8. Remove the end cover (L), dowel pins, O-rings, and end cover gasket.
9. Slip the special tool onto the mainshaft.
Fig. 2: Slipping The Special Tool Onto The Mainshaft
2004 Acura TSX
2004 AUTOMATIC TRANSMISSIONS A/T Overhaul (MCTA) - TSX
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст