Acura TSX / Honda Accord CL. Manual — part 586
14. Reset the ECM/PCM with the HDS.
15. Do the ECM/PCM idle learn procedure (see ECM/PCM IDLE LEARN PROCEDURE ).
16. Check for Temporary DTCs or DTCs in the DTCs MENU with the HDS.
Are any Temporary DTCs or DTCs indicated?
YES: If DTC P0112 is indicated, check for poor connections or loose terminals at the IAT
sensor and the ECM/PCM, then go to step 1 . If any other Temporary DTCs or DTCs are
indicated, go to the indicated DTC troubleshooting.
NO: Troubleshooting is complete.
17. Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM (see
HOW TO SUBSTITUTE THE ECM/PCM ).
18. Check for Temporary DTCs or DTCs in the DTCs MENU with the HDS.
Are any Temporary DTCs or DTCs indicated?
YES: If DTC P0112 is indicated, check for poor connections or loose terminals at the IAT
sensor and the ECM/PCM, then go to step 1 . If any other Temporary DTCs or DTCs are
indicated, go to the indicated DTC troubleshooting.
NO: If the ECM/PCM was updated, troubleshooting is complete. If the ECM/PCM was
substituted, replace the original ECM/PCM (see HOW TO REMOVE THE ECM/PCM
FOR TESTING ).
DTC P0113: IAT SENSOR CIRCUIT HIGH VOLTAGE
1. Turn the ignition switch ON (II).
2. Check the IAT SENSOR in the DATA LIST with the HDS.
Is about -40°F (-40°C) or less, or 4.90 V or higher indicated?
YES: Go to step 3.
NO: Intermittent failure, system is OK at this time. Check for poor connections or loose
terminals at the IAT sensor and the ECM/PCM.
3. Turn the ignition switch OFF.
4. Disconnect the IAT sensor 2P connector.
5. Connect IAT sensor 2P connector terminals No. 1 and No. 2 with a jumper wire.
6. Turn the ignition switch ON (II).
7. Check the IAT SENSOR in the DATA LIST with the HDS.
Is about -40°F (-40°C) or less, or 4.90 V or higher indicated?
YES: Go to step 8.
NO: Go to step 13 .
2004 Acura TSX
2004 ENGINE PERFORMANCE PGM-FI System - TSX
Fig. 11: Connecting IAT Sensor 2P Connector Terminals No. 1 & No. 2 With A Jumper Wire
8. Turn the ignition switch OFF.
9. Remove the jumper wire.
10. Turn the ignition switch ON (II).
11. Measure voltage between IAT sensor 2P connector terminal No. 2 and body ground.
2004 Acura TSX
2004 ENGINE PERFORMANCE PGM-FI System - TSX
Is there about 5 V?
YES: Repair open in the wire between the ECM/PCM (A23) and the IAT sensor, then go to
step 15 .
NO: Go to step 12.
Fig. 12: Measuring Voltage Between IAT Sensor 2P Connector Terminal No. 2 & Body
Ground
2004 Acura TSX
2004 ENGINE PERFORMANCE PGM-FI System - TSX
12. Measure voltage between ECM/PCM connector terminal B17 and body ground.
Is there about 5 V?
YES: Repair open in the wire between the ECM/PCM (B17) and the IAT sensor, then go to
step 15 .
NO: Go to step 19 .
Fig. 13: Measuring Voltage Between ECM/PCM Connector Terminal B17 & Body Ground
2004 Acura TSX
2004 ENGINE PERFORMANCE PGM-FI System - TSX
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст