Acura TSX / Honda Accord CL. Manual — part 982
Fig. 196: Measuring The Resistance Between PCM Connector Terminals C2 & A8 Or A9
11. Disconnect the shift solenoid harness connector at the transmission housing.
12. Measure the resistance between shift solenoid harness connector terminal No. 1 and body ground.
Is there 12-25 ohm?
YES: Repair open in the wire between PCM connector terminal C2 and the shift solenoid
harness connector, then go to step 13.
NO: Check shift solenoid valve C, and check for an open in the shift solenoid harness in the
transmission (see SHIFT SOLENOID VALVE TEST ). Replace shift solenoid valve C
and/or shift solenoid harness, then go to step 13.
2004 Acura TSX
2004 AUTOMATIC TRANSMISSIONS Diagnosis - MCTA 5-Speed
Fig. 197: Measuring The Resistance Between Shift Solenoid Harness Connector Terminal No.
1 & Body Ground
13. Clear the DTC with the HDS.
14. Start the engine in the P position.
15. Check the OBD STATUS in DTCs MENU for a pass/fail test of code P0980.
Did the result indicate a pass?
YES: The problem has been corrected.
NO: Return to step 1 and recheck.
DTC P0982: SHORT IN SHIFT SOLENOID VALVE D CIRCUIT
NOTE:
z
Record all freeze data and review General Troubleshooting Information
(see GENERAL TROUBLESHOOTING INFORMATION ) before you
2004 Acura TSX
2004 AUTOMATIC TRANSMISSIONS Diagnosis - MCTA 5-Speed
1. Clear the DTC with the HDS.
2. Start the engine, and shift the transmission in 2nd gear in the M position.
3. Check that DTC P0982 recurs.
Is DTC P0982 indicated?
YES: Go to step 7 .
NO: Go to step 4.
4. Select SHIFT SOL TEST in MISC. TEST MENU, then carry out A/T SHIFT SOL D test in SHIFT SOL
TEST MENU with the HDS.
5. Start the engine, and shift the transmission in 2nd gear in the M position.
6. Check the OBD STATUS in DTCs MENU for a pass/fail test of code P0982.
Did the result indicate a fail?
YES: Go to step 7.
NO: Intermittent failure, the system is OK at this time. Check the GRN/RED wire for an
intermittent short to ground between the shift solenoid valve D and PCM. If the tester
indicates NOT COMPLETE, return to step 4 and recheck.
7. Turn the ignition switch OFF.
8. Jump the SCS line with the HDS.
9. Disconnect PCM connectors A (31P) and C (22P).
10. Measure the resistance between PCM connector terminals C5 and A8 or A9.
Is there less than 12 ohm?
YES: Go to step 11.
NO: Update the PCM if it does not have the latest software, or substitute a known-good
PCM (see PCM UPDATING & SUBSTITUTION FOR TESTING ), then recheck. If the
symptom/indication goes away with a known-good PCM, replace the original PCM.
troubleshoot.
z
This code is caused by an electrical circuit problem and cannot be caused
by a mechanical problem in the transmission.
2004 Acura TSX
2004 AUTOMATIC TRANSMISSIONS Diagnosis - MCTA 5-Speed
Fig. 198: Measuring The Resistance Between PCM Connector Terminals C5 & A8 Or A9
11. Disconnect the shift solenoid harness connector at the transmission housing.
12. Check for continuity between PCM connector terminals C5 and A8 or A9.
Is there continuity?
YES: Repair short to ground in the wire between PCM connector terminal C5 and the shift
solenoid harness connector, then go to step 13.
NO: Check shift solenoid valve D, and check for a short in the shift solenoid harness in the
transmission (see SHIFT SOLENOID VALVE TEST ). Replace shift solenoid valve D
and/or shift solenoid harness, then go step 13.
2004 Acura TSX
2004 AUTOMATIC TRANSMISSIONS Diagnosis - MCTA 5-Speed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст