Acura MDX (2018 year). Manual — part 12
182
uu
Operating the Switches Around the Steering Wheel
u
Wipers and Washers
Co
ntrols
The rear wiper and washer can be used when
the power mode is in ON.
■
Wiper switch (OFF, INT, ON)
Change the wiper switch setting according to
the amount of rain.
■
Washer (
)
Sprays while you rotate the switch to this
position.
Hold it to activate the wiper and to spray the
washer. Once released, it stops operating
after a few more sweeps.
■
Operating in reverse
When you select the transmission to
(
R with the windshield wipers activated, the
rear wiper operates automatically as follows even if its switch is off.
■
Rear Wiper/Washer
INT: Intermittent
OFF
ON: Continuous wipe
Washer
Windshield Wiper Operation
Rear Wiper Operation
Intermittent
Intermittent
Low speed wipe
High speed wipe
Continuous
18 ACURA MDX-31TZ56400.book 182 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
183
uu
Operating the Switches Around the Steering Wheel
u
Wipers and Washers
Co
ntrols
Turn the headlights on and press the
headlight washer button to operate.
The headlight washers also operate when you
turn the windshield washers for the first time
after the power mode is set to ON.
■
Headlight Washers
Canadian models
1
The headlight washers use the same fluid reservoir as
the windshield washers.
18 ACURA MDX-31TZ56400.book 183 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
184
uu
Operating the Switches Around the Steering Wheel
u
Brightness Control
Co
ntrols
Brightness Control
When the power mode is in ON, you can use
the
(
+ or
(
- button to adjust instrument
panel brightness.
Brighten: Press the
(
+ button.
Dim: Press the
(
- button.
You will hear a beep when the brightness
reaches minimum or maximum. Several
seconds after adjusting the brightness, you
will be returned to the previous display.
■
Brightness level indicator
The brightness level is shown on the MID
while you are adjusting it.
1
Instrument panel brightness varies, depending on
whether the exterior lights are on or off. The
instrument panel dims to reduce glare when they are
on.
When it is bright outside and the headlight
integration with the wiper is activated, the
instrument panel brightness does not change.
To cancel the reduced instrument panel brightness
when the exterior lights are on, press the
(
+ button
until the brightness display is up to max, the beeper
sounds.
The brightness can be set differently for when the
exterior lights are on, and when they are off.
(
+ Button
(
- Button
18 ACURA MDX-31TZ56400.book 184 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
185
uu
Operating the Switches Around the Steering Wheel
u
Rear Defogger/Heated Door Mirror Button
Co
ntrols
Rear Defogger/Heated Door Mirror Button
Press the rear defogger and heated door mirror button to defog the rear window
and mirrors when the power mode is in ON.
The rear defogger and heated door mirrors
automatically switch off after 10-30 minutes
depending on the outside temperature.
Heated Windshield Button
*
Press the heated windshield button to deice
the windshield when the power mode is in
ON.
1
Rear Defogger/Heated Door Mirror Button
NOTICE
When cleaning the inside of the rear window, be
careful not to damage the heating wires.
It is critical to wipe the window from side to side
along the defogger heating wires.
This system consumes a lot of power, so turn it off
when the window has been defogged. Also, do not
use the system for a long time while the engine is
idling. This may weaken the battery, making it
difficult to start the engine.
When the outside temperature is below 41°F (5°C),
the heated door mirror may activate automatically for
10 minutes when you set the power mode to ON.
1
This system consumes a lot of power, so turn it off
when the window has been deiced. Also, do not use
the system for a long period when the engine is
idling. This may weaken the battery, making it
difficult to start the engine.
When the outside temperature is below 39°F (4°C),
the heated windshield may automatically activate.
The system deactivates itself once the outside
temperature reaches 43°F (6°C).
* Not available on all models
18 ACURA MDX-31TZ56400.book 185 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
186
uu
Operating the Switches Around the Steering Wheel
u
Driving Position Memory System
Co
ntrols
Driving Position Memory System
You can store two driver’s seat (except for power lumbar), steering wheel and door
mirror positions with the driving position memory system.
When you unlock and open the driver’s door with a remote transmitter, or keyless
access system, door mirrors adjust to one of the two preset positions and the seat
adjusts to retracted positions of one of the two preset positions automatically.
The steering wheel and the seat will move to the stored position when you set the
power mode to ACCESSORY.
When you enter the vehicle, the MID briefly shows you which remote transmitter
you used to unlock the vehicle.
• DRIVER 1 transmitter is linked to memory button 1.
• DRIVER 2 transmitter is linked to memory button 2.
The driver’s seat moves rearward and steering
wheel fully up depending on the set seating
position once you
• Stop the vehicle.
• Put the transmission in
(
P.
• Turn the engine off.
• Then open the driver’s door.
Once the power mode is in the ACCESSORY
position, the driver’s seat and steering wheel
moves to the DRIVER 1 or 2 preset position.
1
Driving Position Memory System
Using the information screen or MID, you can disable
the automatic seat, steering wheel and door mirrors
adjustment function.
2 Customized Features P. 126, 358
The driver’s seat easy exit feature can be turned ON/
OFF.
2 Customized Features P. 126, 358
System Operation
The system will not operate if:
•
The vehicle speed is above 3 mph (5 km/h).
•
Either memory position button is pressed while the
seat or steering wheel is in motion.
•
The seat or steering wheel position is adjusted
while in operation.
•
The memory 1 or 2 position is set fully to the rear.
DRIVER 1
DRIVER 2
18 ACURA MDX-31TZ56400.book 186 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
187
uu
Operating the Switches Around the Steering Wheel
u
Driving Position Memory System
Co
ntrols
1. Set the power mode to ON. Adjust the
driver’s seat, the steering wheel and the
door mirrors to the desired position.
2. Press the SET button.
u
You will hear the beeper, and the
memory button indicator light will blink.
3. Press and hold memory button
(
1 or
(
2
within five seconds of pressing the SET
button.
u
Once the seat, the steering wheel and
the outside mirror positions have been
memorized, the indicator light on the
button you pressed stays on and you will
hear the double-beep.
1. Put the transmission into
(
P.
2. Apply the parking brake.
3. Press a memory button (
(
1 or
(
2).
u
You will hear the beeper, and the
indicator light will blink.
The seat, the steering wheel and the door
mirrors will automatically move to the
memorized positions. When it has finished
moving, you will hear the beeper, and the
indicator light stays on.
■
Storing a Position in Memory
1
After you press the SET button, the storing operation
will be canceled when:
•
You do not press the memory button within five
seconds.
•
You readjust the seat, the steering wheel or the
outside mirror position before the double-beep.
•
You set the power mode to any position except
ON.
Memory Button 1
Memory Button 2
SET Button
■
Recalling the Stored Position
1
The seat, the steering wheel and the door mirrors will
stop moving if you:
•
Press the SET button or memory button
(
1 or
(
2.
•
Adjust the seat position, door mirrors, or steering
wheel.
•
Put the transmission into a position other than
(
P.
Memory Buttons
18 ACURA MDX-31TZ56400.book 187 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
188
uu
Operating the Switches Around the Steering Wheel
u
Adjusting the Steering Wheel
Co
ntrols
Adjusting the Steering Wheel
The steering wheel height and distance from your body can be adjusted so that you
can comfortably grip the steering wheel in an appropriate driving posture.
Push and hold the adjustment switch to move
the steering wheel in, out, up or down.
u
Make sure you can see the instrument
panel gauges and indicators.
1
3
WARNING
Adjusting the steering wheel position while
driving may cause you to lose control of the
vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the
vehicle is stopped.
Adjustment Switch
18 ACURA MDX-31TZ56400.book 188 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
189
Co
ntrols
Adjusting the Mirrors
Interior Rearview Mirror
Adjust the angle of the rearview mirror when you are sitting in the correct driving
position.
When you are driving after dark, the
automatic dimming rearview mirror and
power door mirrors
*
reduce the glare from
headlights behind you, based on inputs from
the mirror sensor. This feature is always active.
■
Automatic Dimming Rearview Mirror and Power Door
Mirrors
*
1
Keep the inside and outside mirrors clean and
adjusted for best visibility.
Adjust the mirrors before you start driving.
2 Front Seats P. 192
1
Automatic Dimming Rearview Mirror and Power Door Mirrors
The auto dimming function cancels when the
transmission is in
(
R.
* Not available on all models
18 ACURA MDX-31TZ56400.book 189 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
190
uu
Adjusting the Mirrors
u
Power Door Mirrors
Co
ntrols
Power Door Mirrors
You can adjust the door mirrors when the
power mode is set to ON.
■
Mirror position adjustment
L/R selector switch: Select the left or right
mirror. After adjusting the mirror, return the
switch to the center position.
Mirror position adjustment switch: Press
the switch left, right, up, or down to move the
mirror.
■
Folding door mirrors
*
Press the fold button to fold the door mirrors.
If activated, either side door mirror
automatically tilts downward when you put
the transmission into
(
R; this improves close-
in visibility on the selected side of the vehicle
when backing up. The mirror automatically
returns to its original position when you take
the transmission out of
(
R.
To activate this feature, set the power mode
to ON and slide the selector switch to the left
or right side.
Selector Switch
Adjustment Switch
Fold Button
*
■
Reverse Tilt Door Mirror
Selector Switch
* Not available on all models
18 ACURA MDX-31TZ56400.book 190 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
191
uu
Adjusting the Mirrors
u
Power Door Mirrors
Co
ntrols
■
Folding the door mirrors
Lock all doors from outside the vehicle.
u
The mirrors start folding automatically.
2 Locking and Unlocking the Doors P. 139
■
Unfolding the door mirrors
Unlock the driver’s or all doors from outside the vehicle.
u
The mirrors start unfolding automatically.
2 Locking and Unlocking the Doors P. 139
■
Automatic Folding Door Mirror Function
*
1
Automatic Folding Door Mirror Function
Door mirrors will not unfold automatically if fold
button is pressed.
You can turn the automatic folding door mirror
function on and off.
2 Customized Features P. 126, 358
Door mirrors will not fold automatically when locking
from inside the vehicle using lock tab or master door
lock switch.
* Not available on all models
18 ACURA MDX-31TZ56400.book 191 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
192
Co
ntrols
Adjusting the Seats
Front Seats
Adjust the driver’s seat as far back as possible
while allowing you to maintain full control of
the vehicle. You should be able to sit upright,
well back in the seat and be able to
adequately press the pedals without leaning
forward, and grip the steering wheel
comfortably. The passenger’s seat should be
adjusted in a similar manner, so that it is as far
back from the front airbag in the dashboard
as possible.
■
Adjusting the front power seats
1
The National Highway Traffic Safety Administration
and Transport Canada recommend that drivers allow
at least 10 inches (25 cm) between the center of the
steering wheel and the chest.
Always make seat adjustments before driving.
3
WARNING
Sitting too close to a front airbag can result
in serious injury or death if the front
airbags inflate.
Always sit as far back from the front
airbags as possible while maintaining
control of the vehicle.
Move back.
Allow sufficient
space.
■
Adjusting the Seat Positions
Horizontal Position
Adjustment
Height Adjustment
Seat-back Angle
Adjustment
Driver’s Side/
Passenger’s Side
*
Lumbar Support
Adjustment
* Not available on all models
18 ACURA MDX-31TZ56400.book 192 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
193
uu
Adjusting the Seats
u
Front Seats
Co
ntrols
Adjust the driver’s seat-back to a comfortable,
upright position, leaving ample space
between your chest and the airbag cover in
the center of the steering wheel.
The front seat passenger should also adjust
their seat-back to a comfortable, upright
position.
Reclining a seat-back so that the shoulder part of the belt no longer rests against the
occupant’s chest reduces the protective capability of the belt. It also increases the
chance of sliding under the belt in a crash and being seriously injured. The farther a
seat-back is reclined, the greater the risk of injury.
■
Adjusting the Seat-Backs
1
Do not put a cushion, or other object, between the
seat-back and your back. Doing so may interfere with
proper seat belt or airbag operation.
If you cannot get far enough away from the steering
wheel and still reach the controls, we recommend
that you investigate whether some type of adaptive
equipment may help.
3
WARNING
Reclining the seat-back too far can result in
serious injury or death in a crash.
Adjust the seat-back to an upright position,
and sit well back in the seat.
18 ACURA MDX-31TZ56400.book 193 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
194
uu
Adjusting the Seats
u
Second Row Seats
Co
ntrols
Second Row Seats
■
Adjusting the Seat Positions
1
Once a seat is adjusted correctly, rock it back and
forth to make sure it is locked in position.
Seat-back Angle
Adjustment
Pull up the lever to change
the angle.
Horizontal Position
Adjustment
Pull up the bar to move the
seat, then release the bar.
Models with bench seat
18 ACURA MDX-31TZ56400.book 194 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
195
uu
Adjusting the Seats
u
Second Row Seats
Continued
Co
ntrols
Models with captain seat
Seat-back Angle
Adjustment
Pull up the lever to change
the angle.
Horizontal Position
Adjustment
Pull up the bar to move the
seat, then release the bar.
18 ACURA MDX-31TZ56400.book 195 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
uu
Adjusting the Seats
u
Second Row Seats
196
Co
ntrols
Pressing the button on the seat-back, or seat
cushion tilts the second row outer seat's seat-
back forward.
u
The whole seat slides forward.
Pulling up on the strap also tilts the seat-back
forward.
■
Third Row Seat Access
1
The button is disabled when the vehicle is moving.
When you enter the third row seat, be careful not to
trip over the second row seat belt.
Strap
18 ACURA MDX-31TZ56400.book 196 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
197
uu
Adjusting the Seats
u
Second Row Seats
Co
ntrols
Separately fold down the left and right halves of the second row seat to make room
for cargo.
1. Store the center seat belt first. Insert the latch plate into the slot on the side of the
anchor buckle.
2. Retract the seat belt into the holder on the ceiling.
2 Seat Belt with Detachable Anchor P. 38
3. Lower the center head restraint to its lowest position. Put the armrest back into
the seat-back.
4. Pull up on the seat-back angle adjustment
lever.
To return the seat to the original position, pull
up the seat-back in the upright position.
■
Folding Down the Second Row Seat
1
Folding Down the Second Row Seat
Make sure that the folded seat-back does not press
against the front passenger seat, as this can cause the
weight sensors in the front passenger seat to work
improperly.
2 Passenger Front Airbag Off Indicator P. 54
The front seats must be far enough forward so they
do not interfere with the second row seats as they
fold down.
To lock the seat-back upright, push it backwards until
it locks.
Make sure the seat-back, head restraints and seat
cushion are securely latched back into place before
driving. Also, make sure all rear shoulder belts are
positioned in front of the seat-back.
Make sure the center shoulder belt is re-positioned in
the holding slot.
Models with bench seat
Models with bench seat
Lever
All Models
18 ACURA MDX-31TZ56400.book 197 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст