Acura MDX (2018 year). Manual — part 41
646
Han
d
lin
g the U
n
expected
Engine Does Not Start
Checking the Engine
If the engine does not start, check the starter.
Starter condition
Checklist
Starter doesn’t turn or turns
over slowly.
The battery may be dead. Check
each of the items on the right and
respond accordingly.
Check for a message on the MID.
●
If the To Start, Hold Remote Near Start Button message appears
2 If the Keyless Access Remote Battery is Weak P. 647
u
Make sure the keyless access remote is in its operating range.
2 ENGINE START/STOP Button Operating Range P. 169
Check the brightness of the interior lights.
Turn on the interior lights and check the brightness.
●
If the interior lights are dim or do not come on at all
●
If the interior lights come on normally
The starter turns over normally
but the engine doesn’t start.
There may be a problem with the
fuse. Check each of the items on
the right and respond accordingly.
Review the engine start procedure.
Follow its instructions, and try to start the engine again.
2 Starting the Engine P. 465
Check the immobilizer system indicator.
When the immobilizer system indicator is blinking, the engine cannot be started.
2 Immobilizer System P. 163
Check the fuel level.
There should be enough fuel in the tank.
Check the fuse.
Check all fuses, or have the vehicle checked by a dealer.
2 Inspecting and Changing Fuses P. 665
If the problem continues:
1
If you must start the vehicle immediately, use an
assisting vehicle or booster battery to jump start it.
18 ACURA MDX-31TZ56400.book 646 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
647
uu
Engine Does Not Start
u
If the Keyless Access Remote Battery is Weak
Han
d
lin
g the U
n
expected
If the Keyless Access Remote Battery is Weak
If the beeper sounds, the To Start, Hold Remote Near Start Button message
appears on the multi-information display, and the indicator on the ENGINE START/
STOP button flashes, and the engine won’t start, start the engine as follows:
1. Touch the center of the ENGINE START/
STOP button with the A logo on the keyless
access remote while the indicator on the
ENGINE START/STOP button is flashing.
The buttons on the keyless access remote
should be facing you.
u
The indicator flashes for about 30
seconds.
2. Depress the brake pedal and press the
ENGINE START/STOP button within 10
seconds after the beeper sounds while the
indicator stays on.
u
If you don’t depress the pedal, the mode
will change to ACCESSORY.
ENGINE
START
STOP
18 ACURA MDX-31TZ56400.book 647 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
648
uu
Engine Does Not Start
u
Emergency Engine Stop
Han
d
lin
g the U
n
expected
Emergency Engine Stop
The ENGINE START/STOP button may be used to stop the engine due to an
emergency situation even while driving. If you must stop the engine, do either of the
following operations:
• Press and hold the ENGINE START/STOP button for about two seconds.
• Firmly press the ENGINE START/STOP button three times.
The steering wheel will not lock. However, because turning off the engine disables
the power assist the engine provides to the steering and braking systems, it will
require significantly more physical effort and time to steer and slow the vehicle. Use
both feet on the brake pedal to slow down the vehicle and stop immediately in a
safe place.
The gear position automatically changes to
(
P after the vehicle comes to a complete
stop. Then, the power mode changes to VEHICLE OFF.
The gear position automatically changes to P after the vehicle comes to a complete
stop. Then press the ENGINE START/STOP button twice without depressing the
brake pedal to change the mode to VEHICLE OFF.
1
Do not press the button while driving unless it is
absolutely necessary for the engine to be turned off.
U.S. models
Canadian models
18 ACURA MDX-31TZ56400.book 648 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
649
Continued
Han
d
lin
g the U
n
expected
Jump Starting
Turn off the power to electric devices, such as audio and lights. Turn off the engine,
then open the hood.
1. Pull up on the engine cover, remove it from
the pins.
u
Start on the passenger side and lift the
outermost edge of the cover.
u
Move towards the driver side while
applying uniform upward pressure.
2. Connect the first jumper cable to your
vehicle’s battery + terminal.
3. Connect the other end of the first jumper
cable to the booster battery + terminal.
u
Use a 12-volt booster battery only.
u
When using an automotive battery
charger to boost your 12-volt battery,
select a lower charging voltage than 15
volt. Check the charger manual for the
proper setting.
4. Connect the second jumper cable to the
booster battery - terminal.
■
Jump Starting Procedure
1
Securely attach the jumper cables clips so that they
do not come off when the engine vibrates. Also be
careful not to tangle the jumper cables or allow the
cable ends to touch each other while attaching or
detaching the jumper cables.
Battery performance degrades in cold conditions and
may prevent the engine from starting.
3
WARNING
A battery can explode if you do not follow
the correct procedure, seriously injuring
anyone nearby.
Keep all sparks, open flames, and smoking
materials away from the battery.
Engine Cover
Pin
Booster Battery
18 ACURA MDX-31TZ56400.book 649 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
650
uu
Jump Starting
u
Han
d
lin
g the U
n
expected
5. Connect the other end of the second
jumper cable to the engine hanger as
shown. Do not connect this jumper cable to
any other part.
6. If your vehicle is connected to another
vehicle, start the assisting vehicle’s engine
and increase its rpm slightly.
7. Attempt to start your vehicle’s engine. If it
turns over slowly, check that the jumper
cables have good metal-to-metal contact.
Once your vehicle’s engine has started, remove the jumper cables in the following
order.
1. Disconnect the jumper cable from your vehicle’s ground.
2. Disconnect the other end of the jumper cable from the booster battery -
terminal.
3. Disconnect the jumper cable from your vehicle’s battery + terminal.
4. Disconnect the other end of the jumper cable from the booster battery +
terminal.
Have your vehicle inspected by a nearby service station or a dealer.
■
What to Do After the Engine Starts
18 ACURA MDX-31TZ56400.book 650 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
651
Continued
Han
d
lin
g the U
n
expected
Overheating
How to Handle Overheating
Overheating symptoms are as follows:
• The temperature gauge needle is at the
mark or the engine suddenly loses
power.
• The Stop Driving When Safe. Engine Temperature Too Hot message appears
on the multi-information display (MID).
• Steam or spray comes out of the engine compartment.
■
First thing to do
1. Immediately park the vehicle in a safe place.
2. Turn off all accessories and turn on the hazard warning lights.
u
No steam or spray present: Keep the engine running and open the hood.
u
Steam or spray is present: Turn off the engine and wait until it subsides.
Then, open the hood.
1
NOTICE
Continuing to drive with the temperature gauge
needle at the
mark may damage the engine.
3
WARNING
Steam and spray from an overheated
engine can seriously scald you.
Do not open the hood if steam is coming
out.
H
H
18 ACURA MDX-31TZ56400.book 651 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
uu
Overheating
u
How to Handle Overheating
652
Han
d
lin
g the U
n
expected
■
Next thing to do
1. Check that the cooling fan is operating and
stop the engine once the temperature
gauge needle comes down.
u
If the cooling fan is not operating,
immediately stop the engine.
2. Once the engine has cooled down, inspect
the coolant level and check the cooling
system components for leaks.
u
If the coolant level in the reserve tank is
low, add coolant until it reaches the
MAX mark.
u
If there is no coolant in the reserve tank,
check that the radiator is cool. Cover the
radiator cap with a heavy cloth and open
the cap. If necessary, add coolant up to
the base of the filler neck, and put the
cap back on.
■
Last thing to do
Once the engine has cooled sufficiently, restart it and check the temperature gauge.
If the temperature gauge needle has gone down, resume driving. If it has not gone
down, contact a dealer for repairs.
1
If the coolant is leaking, contact a dealer for repairs.
Use water as an emergency/temporary measure only.
Have a dealer flush the system with proper antifreeze
as soon as possible.
Continuing to drive with the Stop Driving When
Safe. Engine Temperature Too Hot message on
the multi-information display may damage the
engine.
3
WARNING
Removing the radiator cap while the
engine is hot can cause the coolant to spray
out, seriously scalding you.
Always let the engine and radiator cool
down before removing the radiator cap.
Reserve Tank
MAX
MIN
18 ACURA MDX-31TZ56400.book 652 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
653
Han
d
lin
g the U
n
expected
Indicator, Coming On/Blinking
If the Low Oil Pressure Indicator Comes On
■
Reasons for the indicator to come on
Comes on when the engine oil pressure is low.
■
What to do as soon as the indicator comes on
1. Immediately park the vehicle on level ground in a safe place.
2. If necessary, turn the hazard warning lights on.
■
What to do after parking the vehicle
1. Stop the engine and let it sit for approximately three minutes.
2. Open the hood and check the oil level.
3. Start the engine and check the low oil pressure indicator.
u
The indicator goes off: Start driving again.
u
The indicator does not go off within 10 seconds: Immediately stop
the engine and contact a dealer for repairs.
If the Charging System Indicator Comes On
■
Reasons for the indicator to come on
Comes on when the battery is not being charged.
■
What to do when the indicator comes on
Turn off the climate control system, rear defogger, and other electrical
systems, and immediately contact a dealer for repairs.
1
If the Low Oil Pressure Indicator Comes On
NOTICE
Running the engine with low oil pressure can cause
serious mechanical damage almost immediately.
1
If the Charging System Indicator Comes On
If you need to stop temporarily, do not turn off the
engine. Restarting the engine may rapidly discharge
the battery.
18 ACURA MDX-31TZ56400.book 653 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
654
uu
Indicator, Coming On/Blinking
u
If the Malfunction Indicator Lamp Comes On or Blinks
Han
d
lin
g the U
n
expected
If the Malfunction Indicator Lamp Comes On or
Blinks
■
Reasons for the indicator lamp to come on or blink
• Comes on when there is a problem with the engine emissions control
system.
• Blinks when engine misfiring is detected.
■
What to do when the indicator lamp comes on
Avoid high speeds and immediately get your vehicle inspected at a
dealer.
■
What to do when the indicator lamp blinks
Park the vehicle in a safe place with no flammable items and wait at least
10 minutes or more with the engine stopped until it cools.
1
If the Malfunction Indicator Lamp Comes On or Blinks
NOTICE
If you drive with the malfunction indicator lamp on,
the emissions control system and the engine could be
damaged.
If the malfunction indicator lamp blinks again when
restarting the engine, drive to the nearest dealer at
31 mph (50 km/h) or less. Have your vehicle
inspected.
18 ACURA MDX-31TZ56400.book 654 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
655
uu
Indicator, Coming On/Blinking
u
If the Brake System Indicator (Red) Comes On
Han
d
lin
g the U
n
expected
If the Brake System Indicator (Red) Comes On
■
Reasons for the indicator to come on
• The brake fluid is low.
• There is a malfunction in the brake system.
■
What to do when the indicator comes on while driving
Depress the brake pedal lightly to check pedal pressure.
• If normal, check the brake fluid level the next time you stop.
• If abnormal, take immediate action. If necessary, downshift the
transmission to slow the vehicle using engine braking.
If the Speed-Sensitive Electric Power Steering (EPS)
System Indicator Comes On
■
Reasons for the indicator to come on
• Comes on when there is a problem with the EPS system.
• If you depress the accelerator pedal repeatedly to increase the engine
speed while the engine is idling, the indicator comes on, and
sometimes the steering wheel becomes harder to operate.
■
What to do when the indicator comes on
Stop the vehicle in a safe place and restart the engine.
If the indicator comes on and stays on, immediately have your vehicle
inspected by a dealer.
1
If the Brake System Indicator (Red) Comes On
Have your vehicle repaired immediately.
It is dangerous to drive with low brake fluid. If there
is no resistance from the brake pedal, stop
immediately in a safe place. If necessary downshift
the gears.
If the brake system indicator and ABS indicator come
on simultaneously, the electronic brake distribution
system is not working. This can result in vehicle
instability under sudden braking.
Have your vehicle inspected by a dealer immediately.
U.S.
Canada
18 ACURA MDX-31TZ56400.book 655 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
656
uu
Indicator, Coming On/Blinking
u
If the Electric Parking Brake System Indicator Comes On
Han
d
lin
g the U
n
expected
If the Electric Parking Brake System Indicator Comes
On
■
Reasons for the indicator to come on
Comes on when there is a problem with the electric parking brake
system.
■
What to do when the indicator comes on
Avoid using the parking brake and immediately get your vehicle
inspected at a dealer.
■
What to do when the electric parking brake indicator comes on
or blinks at the same time
Release the parking brake.
2 Parking Brake P. 528
• If the electric parking brake indicator remains on or blinks even after
releasing the parking brake, immediately stop the vehicle in a safe
place and call a dealer.
u
To prevent your vehicle from moving, change the gear position to
(
P.
• If only the electric parking brake indicator goes off, immediately get
your vehicle inspected at a dealer.
1
If the Electric Parking Brake System Indicator Comes On
If you apply the parking brake, it may not release.
If the electric parking brake indicator also turns on,
the parking brake is still applied.
When the electric parking brake indicator blinks at
the same time as the electric parking brake system
indicator, the system must be checked. The parking
brake may not operate under these conditions.
18 ACURA MDX-31TZ56400.book 656 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
657
uu
Indicator, Coming On/Blinking
u
If the Low Tire Pressure/TPMS Indicator Comes On or Blinks
Han
d
lin
g the U
n
expected
If the Low Tire Pressure/TPMS Indicator Comes On or
Blinks
■
Reasons for the indicator to come on or blink
A tire pressure is significantly low. If there is a problem with the TPMS
with Tire Fill Assist or the compact spare tire
*
is installed, the indicator
blinks for about one minute, and then stays on.
■
What to do when the indicator comes on
Drive carefully and avoid abrupt cornering and hard braking.
Stop your vehicle in a safe place. Check the tire pressure and adjust the
pressure to the specified level. The specified tire pressure is on a label on
the driver side doorjamb.
■
What to do when the indicator blinks
Have the tire inspected by a dealer as soon as possible. If the compact
spare tire
*
causes the indicator to blink, change the tire to a full-size tire.
The indicator goes off after driving for a few miles (kilometers).
If the Transmission System Indicator Blinks along
with the Warning Message
■
Reasons for the indicator to blink
There is a problem with the transmission system.
■
What to do when the indicator blinks
• Immediately have your vehicle inspected by a dealer.
• Select
(
N after starting the engine.
u
Check if the
(
N position in the instrument panel and the indicator
on the
(
N button light/blink.
u
The engine cannot be turned on unless the parking brake is set.
2 Starting the Engine P. 465
1
If the Low Tire Pressure/TPMS Indicator Comes On or Blinks
NOTICE
Driving on an extremely underinflated tire can cause
it to overheat. An overheated tire can fail. Always
inflate your tires to the prescribed level.
TPMS Fill Assist provides visual and audible assistance
during tire pressure adjustment. With the power
mode in ON, while you adjust tire pressure up or
down, the system alerts you as follows:
Below recommended pressure: The beeper
sounds and exterior lights flash once every five
seconds.
At recommended pressure: The beeper sounds
and exterior lights flash rapidly for ~ five seconds.
Above recommended pressure: The beeper
sounds and lights flash twice every three seconds.
1
If the Transmission System Indicator Blinks along with the
Warning Message
You may not be able to start the engine.
Make sure to set the parking brake when parking
your vehicle.
Call a professional towing service if you need to tow
your vehicle.
* Not available on all models
18 ACURA MDX-31TZ56400.book 657 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
658
Han
d
lin
g the U
n
expected
Fuses
Fuse Locations
If any electrical devices are not working, set
the power mode to VEHICLE OFF (LOCK)
and check to see if any applicable fuse is
blown.
Fuse locations are shown on the fuse box
cover. Locate the fuse in question by the
fuse number and box cover number.
Located near the brake fluid reservoir. Push
the tabs to open the box.
■
Engine Compartment Fuse
Box Type A
Tab
■
Circuit protected and fuse rating
Circuit Protected
Amps
1
STRLD
*2
7.5 A
2
−
−
3
ACG FR
15 A
4
Washer
15 A
5
IG1 OP
*1
(7.5 A)
6
ECU FR
7.5 A
7
VBSOL
*1
(10 A)
Starter
*2
7.5 A
8
FI Sub
15 A
9
DBW
15 A
10
FI Main
15 A
11
IG Coil
15 A
12
DRL R
10 A
13
DRL L
10 A
14
Injector
20 A
15
Radio
*1
20 A
*1:Models without Auto Idle Stop
*2:Models with Auto Idle Stop
16
Back Up
10 A
17
MG Clutch
(7.5 A)
18
FR Fog
*
7.5 A
19
−
−
20
H/L HI R
7.5 A
21
−
−
22
Small
*1
10 A
23
−
−
24
H/L HI L
7.5 A
25
SBW
15 A
26
H/L LO R
10 A
27
H/L LO L
10 A
28
Oil LVL
7.5 A
29
Main Fan
30 A
30
Sub Fan
30 A
31
Wiper Main
30 A
Circuit Protected
Amps
* Not available on all models
18 ACURA MDX-31TZ56400.book 658 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
659
uu
Fuses
u
Fuse Locations
Continued
Han
d
lin
g the U
n
expected
Fuse locations are shown on the fuse box
cover. Locate the fuse in question by the
fuse number and box cover number.
Located near the battery. Push the tabs to
open the box.
■
Engine Compartment Fuse
Box Type B
Tab
■
Circuit protected and fuse rating
Circuit Protected
Amps
1
Main Fuse
150 A
2
VSA MTR
40 A
VSA FSR
20 A
Stop&Horn Hazard
*
30 A
Hazard
*
RR BLOWER&BMS
30 A
DC/DC 3
*
60 A
RR F/B-2
60 A
AS F/B-2
60 A
EPS
60 A
3
H/L Washer
*
(30 A)
IG1B Main
30 A
R/B Main
60 A
DR F/B-1
50 A
AS F/B-1
50 A
RR F/B-1
60 A
IG1A Main
30 A
DR F/B-2
50 A
4
FI Main
40 A
5
FR Blower
40 A
6
RR DEF
40 A
7
IG1 Main ST
30 A
8
Stop & Horn
*
20 A
Stop
*
10 A
9
Hazard
10 A
10
BMS
7.5 A
11
Small LT
*
7.5 A
Circuit Protected
Amps
* Not available on all models
18 ACURA MDX-31TZ56400.book 659 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
660
uu
Fuses
u
Fuse Locations
Han
d
lin
g the U
n
expected
Located near the + terminal on the battery.
Pull up the cover.
Replacement of this fuse should be done by
a dealer.
Fuse location is shown on the back of the
positive battery terminal cover.
■
Engine Compartment Fuse
Box Type C
Fuse
Positive Battery
Terminal Cover
■
Circuit protected and fuse rating
Circuit Protected
Amps
Fan Main
60 A
18 ACURA MDX-31TZ56400.book 660 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
661
uu
Fuses
u
Fuse Locations
Continued
Han
d
lin
g the U
n
expected
Located under the dashboard.
Fuse locations are shown on the label on
the outer side of the side panel cover.
Locate the fuse in question by the fuse
number and label number.
■
Driver’s Side Interior Fuse Box
Type A
Fuse Box
Fuse Label
■
Circuit protected and fuse rating
Circuit Protected
Amps
1
AS Door Lock
10 A
2
RR DR Door Lock
7.5 A
3
DR Door Lock
7.5 A
4
FR AS Door Unlock
10 A
5
RR DR Door Unlock
7.5 A
6
DR Door Unlock
(7.5 A)
7
D/L Main
20 A
8
−
−
9
ETS TELE
20 A
10
IG1 RR
15 A
11
Meter
*
7.5 A
Shifter
*
12
IG1 FR
20 A
13
ACC
7.5 A
14
−
−
15
DR P/Seat (SLI)
20 A
16
S/R
20 A
17
RR DR P/W
20 A
18
Smart
10 A
19
FR DR P/W
20 A
20
−
−
21
Fuel Pump
20 A
22
IG1 AS
15 A
23
ABS/VSA
*
Smart
*
7.5 A
24
ACG AS
7.5 A
25
STRLD
*
7.5 A
26
IG2 HAC
7.5 A
27
DRL
7.5 A
28
ACC Key Lock
7.5 A
29
DR P/Seat (LUM)
7.5 A
30
INT Lights
7.5 A
31
ETS TILT
20 A
32
DR P/Seat (REC)
20 A
33
−
−
34
−
−
Circuit Protected
Amps
* Not available on all models
18 ACURA MDX-31TZ56400.book 661 ページ 2017年8月23日 水曜日 午後4時1分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст