Acura CSX. Manual — part 637
01
SNR9AGTJ10311157191KDAT02
01
SNR9A0DJ10370327201KBAT80
Type S model
Front Door Speaker
23-259
23-259
Stereo Amplifier Removal/
Installation
Speaker Replacement
A
C
B
A
B
C
B
1. Slide the driver’s front seat forward fully.
2. Remove the amp cover (A), then disconnect the
connectors (B).
3. Remove the mounting bolts, then remove the
stereo amplifier (C).
4. Install the stereo amplifier in the reverse order of
removal.
1. Remove the front door panel (see page 20-7).
2. Remove the screw. Then lift the speaker (A) straight
up to release the lower clips (B).
3. Disconnect the 2P connector (C), and remove the
speaker.
4. Install the speaker in the reverse order of removal.
08/08/21 14:14:17 61SNR030_230_0262
02
*01
04
05
Tweeter
Rear Speaker
23-260
Audio System
A
B
A
A
A
C
B
1. Carefully pry the tweeter grille (A) out of the
dashboard. Be careful not to damage the tweeter
grille and the dashboard.
2. Disconnect the 2P connector (B) from the tweeter.
3. Remove the tweeter (A) from the speaker grille.
4. Install the tweeter in the reverse order of removal.
1. Remove the rear speaker grille (A).
2. Remove the screw. Then lift the speaker (A) straight
up to release the clips (B).
3. Disconnect the 2P connector (C), and remove the
speaker.
4. Install the speaker in the reverse order of removal.
08/08/21 14:14:18 61SNR030_230_0263
01
*01
SNR9A0DJ10300013431KBAT00
Subwoofer (Type S model)
23-261
23-261
Auxiliary Jack Assembly
Replacement
A
B
A
B
1. Remove the rear tray (see page 20-78).
2. Remove the four mounting bolts from the
subwoofer (A).
3. Disconnect the 2P connector (B), and remove the
subwoofer.
4. Install the subwoofer in the reverse order of
removal.
1. With navigation: Remove the navigation unit
(see page 23-355).
Without navigation: Remove the audio unit
(see page 23-256).
2. Carefully pull out the auxiliary jack assembly (A),
then disconnect the 5P connector (B).
3. Install the auxiliary jack assembly in the reverse
order of removal.
08/08/21 14:14:18 61SNR030_230_0264
*01
SNR9A0DJ10300062333KBAT02
+
−
▲
▼
01
SNR9A0DJ10311113145FEAT00
Position
Resistance
23-262
23-262
Audio System
USB Adapter Replacement
Audio Remote Switch Test
B
C
D
A
A
B
1. Remove the center console (see page 20-92).
2. Detach the USB adapter cable (A) from the clip.
Remove the cover (B) and disconnect the USB
adapter cable connector (C).
3. Carefully pull out the USB adapter holder (D) from
the center console box.
4. Install the USB adapter in the reverse order of
removal.
SRS components are located in this area. Review the
SRS component location (see page 24-11).
Also review the precautions and procedures (see page
24-13) in the SRS section before doing repairs or
service.
1. Remove the driver’s airbag assembly (see page
24-188).
2. Remove the 20P connector (A) from the cable reel
(B).
3. Measure the resistance between terminals No. 9
and No. 10 in each switch position according to the
table.
No button
pressed
About 10 k
MODE
About 3.7 k
CH (
)
About 1.7 k
CH (
)
About 775
(VOL.UP)
About 357
(VOL.DOWN)
About 100
4. If the resistance is not as specified, replace the
audio remote switch (see page 23-263).
08/08/21 14:14:18 61SNR030_230_0265
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст