Acura CSX. Manual — part 54
10
02
12
6-65
A
B
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
B
A
A
B
19. Connect the positive crankcase ventilation (PCV)
hose (A) (K20Z2 engine) and install the ground
cable (B).
20. Connect the fuel feed hose (A) (see page 11-331),
then install the quick-connect fitting cover (B).
21. Connect the evaporative emission (EVAP) canister
hose (A) and the brake booster vacuum hose (B).
22. Install the exhaust manifold (see page 9-11).
23. Install the intake manifold:
• K20Z2 engine (see page 9-4)
• K20Z3 engine (see page 9-9)
24. Install the drive belt (see page 4-31).
25. Install the air cleaner assembly (see page 11-345).
26. After installation, check that all tubes, hoses and
connectors are installed correctly.
27. Inspect for fuel leaks. Turn the ignition switch to
ON (II) (do not operate the starter) so that the fuel
pump runs for about 2 seconds and pressurizes the
fuel line. Repeat this operation three times, then
check for fuel leakage at any point in the fuel line.
*01
SNR9A00A14600017841KCAT00
6-66
6-66
Cylinder Head
Sealing Bolt Installation
A
22 x 1.5 mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)
B
28. Refill the radiator with engine coolant, and bleed
the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
29. Do the engine control module (ECM)/powertrain
control module (PCM) idle lean procedure
(see page 11-310).
30. Do the crankshaft position (CKP) pattern clear/CKP
pattern lean procedure (see page 11-4).
31. Inspect the idle speed (see page 11-309).
32. Inspect the ignition timing (see page 4-20).
NOTE: When installing the sealing bolt (A), always use
a new washer (B).
Replace.
SNR9A000000000J0701ZCAT00
Engine Mechanical
Engine Block
. . . . . . . . . . . . . . . .
. . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . .
. . . . . .
. . . . . . . . . . . . . . ..
. . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . ...
. . . . . . . . . . . . ..
. .
. . . . . . . . . . .
. . . . . . . . . . . . . .
. . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . . . ..
. . . . . . . . . . . . ...
. . . . . . . . . . . ..
. . . . . . . . . . . . . . . .
. . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . .
. . . . . .
. . . . . . . . . . . . . . ..
. . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . ...
. . . . . . . . . . . . ..
. .
. . . . . . . . . . .
. . . . . . . . . . . . . .
. . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . . . ..
. . . . . . . . . . . . ...
. . . . . . . . . . . ..
Special Tools
. 7-2
Component Location Index
. 7-3
Connecting Rod and Crankshaft End Play
Inspection
. 7-5
Crankshaft Main Bearing Replacement
. 7-6
Connecting Rod Bearing Replacement
. 7-8
Oil Pan Removal
. 7-11
Crankshaft and Piston Removal
. 7-13
Crankshaft Inspection
. 7-15
Block and Piston Inspection
. 7-16
Cylinder Bore Honing
. 7-18
Piston, Pin, and Connecting Rod Replacement
. 7-18
Piston Ring Replacement
. 7-21
Piston Installation
. 7-23
Connecting Rod Bolt Inspection
. 7-25
Crankshaft Installation
. 7-25
Oil Pan Installation
. 7-29
Transmission End Crankshaft Oil Seal
Installation - In Car
. 7-32
Sealing Bolt Installation
. 7-33
01
01
01
SNR9A000000000J0701PAAT00
Ref. No.
Tool Number
Description
Qty
7-2
Engine Block
Special Tools
07ZAD-PNAA100
Oil Seal Driver Attachment 96
1
07746-0010700
Attachment, 24 x 26 mm
1
07749-0010000
Driver
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст