Acura CSX. Manual — part 132
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
11-202
PGM-FI System
64. Turn the ignition switch to LOCK (0).
65. Reconnect the ABS modulator-control unit 25P
connector (or the yaw rate-lateral acceleration
sensor 4P connector).
66. Disconnect SRS unit connector A (28P).
67. Turn the ignition switch to ON (II), and read the
HDS.
Replace the SRS unit (see page 24-203).
Go to step 68.
68. Turn the ignition switch to LOCK (0).
69. Reconnect SRS unit connector A (28P).
70. Disconnect EPS control unit connector D (28P).
71. Turn the ignition switch to ON (II), and read the
HDS.
Replace the EPS control unit (see page 17-84).
• With TPMS: Go to step 72.
• Without TPMS: Update the ECM/PCM if it does
not have the latest software (see page 11-227), or
substitute a known-good ECM/PCM (see page
11-7), then recheck. If the symptom/indication
goes away with a known-good ECM/PCM,
replace the original ECM/PCM (see page 11-228).
72. Turn the ignition switch to LOCK (0).
73. Reconnect EPS control unit connector D (28P).
74. Disconnect the TPMS control unit 20P connector.
75. Turn the ignition switch to ON (II), and read the
HDS.
Replace the TPMS control unit (see page
18-75).
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
Does the HDS identif y the vehicle?
Does the HDS identif y the vehicle?
Does the HDS identif y the vehicle?
08/08/21 14:21:54 61SNR030_110_0202
01
SNR9A00A20326939902FAAT00
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
11-203
MIL Circuit Troubleshooting
ECM/PCM CONNECTOR A (44P)
SCS (BRN)
1. Turn the ignition switch to ON (II).
2. Do the gauge self-diagnostic function (see page
22-241).
Go to step 3.
Substitute a known-good gauge control
module (tach), and recheck. If the MIL circuit is OK,
replace the original gauge control module (tach)
(see page 22-277).
3. Connect the HDS to the DLC (see page 11-3).
4. Check the SCS in the DATA LIST with the HDS.
Go to step 5.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
5. Turn the ignition switch to LOCK (0).
6. Disconnect ECM/PCM connector A (44P), then
disconnect the HDS.
7. Check for continuity between ECM/PCM connector
terminal A31 and body ground.
Repair short in the wire between the ECM/
PCM (A31) and the SRS unit, the DLC.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
Terminal side of female terminals
Does the MIL indicator f lash?
Is a shor t indicated?
Is ther e continuity?
08/08/21 14:21:54 61SNR030_110_0203
SNR9A00A20326919461FAAT00
−
−
−
−
−
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
11-204
PGM-FI System
DLC Circuit Troubleshooting
NOTE: Make sure the HDS and the HDS DLC cable are
not detective.
1. Turn the ignition switch to LOCK (0).
2. Connect the HDS to the DLC (see page 11-3).
NOTE: Make sure the HDS is properly connected to
the DLC.
3. Turn the ignition switch to ON (II), and read the
HDS.
Go to step 4.
Go to step 25.
4. Check for Temporary DTCs or DTCs in the PGM-FI
system with the HDS.
Go to the indicated DTC’s troubleshooting.
Go to step 5.
5. Turn the ignition switch to LOCK (0).
6. Turn the ignition switch to ON (II), and watch the
SRS indicator.
Go to the SRS system’s general
troubleshooting information (see page 24-22).
• With ABS: Go to step 7.
• With VSA system: Go to step 9.
7. Turn the ignition switch to LOCK (0).
8. Turn the ignition switch to ON (II), and watch the
ABS indicator.
Go to the ABS’s general troubleshooting
information (see page 19-49).
Go to step 11.
9. Turn the ignition switch to LOCK (0).
10. Turn the ignition switch to ON (II), and watch the
VSA indicator.
Go to the VSA system’s general
troubleshooting information (see page 19-97).
Go to step 11.
11. Turn the ignition switch to LOCK (0).
12. Start the engine, and watch the EPS indicator.
Go to the EPS system’s general
troubleshooting information (see page 17-19).
Go to step 13.
Does the HDS identif y the vehicle?
Ar e any T empor ar y DT Cs or DT Cs indicated?
Does the SRS indicator stay on?
Does the ABS indicator stay on?
Does the V SA indicator stay on?
Does the EPS indicator stay on?
08/08/21 14:21:54 61SNR030_110_0204
01
−
−
−
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
11-205
DATA LINK CONNECTOR (DLC)
K-LINE (LT BLU)
13. Turn the ignition switch to LOCK (0).
14. Turn the ignition switch to ON (II), and watch the
immobilizer indicator.
Go to the immobilizer system’s
troubleshooting (see page 22-315).
• With TPMS: Go to step 15.
• Without TPMS: Go to step 17.
15. Turn the ignition switch to LOCK (0).
16. Turn the ignition switch to ON (II), and watch the
TPMS indicator.
Go to the TPMS’s general troubleshooting
information (see page 18-49).
Go to step 17.
17. Do the gauge self-diagnostic function (see page
22-241).
18. Check for B-CAN system DTCs without the HDS
(see page 22-74).
Go to the indicated DTC’s troubleshooting.
Go to step 19.
19. Turn the ignition switch to LOCK (0).
20. Disconnect the HDS from the DLC.
21. Check for continuity between DLC terminal No. 7
and body ground.
Go to step 22.
Go to step 23.
22. Continue to check for continuity between DLC
terminal No. 7 and body ground, while
disconnecting these parts, one at a time:
• SRS unit connector A (28P)
• ABS modulator-control unit 25P connector (with
ABS)
• VSA modulator-control unit 37P connector (with
VSA system)
• EPS control unit connector D (28P)
• Immobilizer-keyless control unit 7P connector
• TPMS control unit 20P connector (with TPMS)
• Audio unit 17P connector
• Under-dash fuse/relay box Q (16P) connector
Replace the part that caused an open when it
was disconnected.
Repair short in the wire between the DLC (K-
line) and the ABS modulator-control unit (with
ABS), the VSA modulator-control unit (with VSA
system), the SRS unit, the EPS control unit, the
immobilizer-keyless control unit, the audio unit, the
TPMS control unit (with TPMS), or the under-dash
fuse/relay box.
Terminal side of female terminals
Does the immobilizer indicator stay on or f lash?
Does the T PMS indicator stay on?
Ar e any B-CAN DT Cs indicated?
Is ther e continuity?
Does continuity go away when one of the above
connector s is disconnected?
08/08/21 14:21:54 61SNR030_110_0205
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст