Acura CSX. Manual — part 432
02
09
10
Fasteners adhesive tape:
Thickness 0.8 mm (0.031 in.)
Width 9 mm (0.35 in.)
20-50
Glass
Fastener Locations
: Fastener, 2
Fastener Locations
: Fastener, 2
A
B
: Apply glass primer here.
A
B
B
C
Inside
11 mm
(0.43 in.)
Inside
11 mm
(0.43 in.)
A
B
B
B
A
A
5.5 mm
(0.22 in.)
5.5 mm
(0.22 in.)
14. Attach the fasteners with adhesive tape to the rear
window opening flange of the body on both sides.
15. Set the rear window in the opening, and center it.
Make alignment marks (A) across the rear window
and the body with a grease pencil at the four points
are shown:
• Make sure both upper clips (B) are in the body
holes.
• Be careful not to touch the rear window where
adhesive will be applied.
16. Remove the rear window.
17. Apply a light coat of glass primer with a sponge
applicator along the edge of the rear window (A)
between the dams (B) as shown, then lightly wipe it
off with gauze or cheesecloth:
• With the printed dots (C) on the rear window as a
guide, apply the glass primer to both lower
corner portions of the rear window.
• Do not apply body primer to the rear window,
and do not get body and glass primer sponge
applicators mixed up.
• Never touch the primed surfaces with your hands.
If you do, the adhesive may not bond to the rear
window properly, causing a leak after the rear
window is installed.
• Keep water, dust, and abrasive materials away
from primed surfaces.
08/08/21 15:00:14 61SNR030_200_0052
11
12
13
20-51
: Apply body primer to exposed point as shown.
16 mm
(0.63 in.)
16 mm
(0.63 in.)
16 mm
(0.63 in.)
12 mm (0.47 in.)
7 mm (0.28 in.)
A
Inside
12 mm
(0.47 in.)
7 mm (0.28 in.)
A
B
C
D
A
A
A
B
B
B
C
C
C
C
A
Inside
2 mm
(0.08 in.)
2 mm
(0.08 in.)
2 mm
(0.08 in.)
2 mm
(0.08 in.)
18. Carefully apply a light coat of body primer with a
sponge to any exposed paint or metal around the
flange where new adhesive will be applied. Let the
primer dry for at least 10 minutes:
• Do not apply body primer to any remaining
original adhesive on the flange.
• Be careful not to mix up the body and glass
primer sponge applicators.
• Never touch the primed surfaces with your hands.
19. Cut a ‘‘V’’ in the end of the nozzle (A) on the
adhesive cartridge as shown.
20. Put the cartridge in a caulking gun, and run a
continuous bead of adhesive (A) around the edge
of the rear window (B) between the dams (C) as
shown:
• With the printed dots (D) on the rear window as a
guide, apply the adhesive to both side portions of
the rear window.
• Apply the adhesive within 30 minutes after
applying the glass primer. Make a slightly thicker
bead at each corner.
08/08/21 15:00:15 61SNR030_200_0053
20-52
Glass
21. Hold the rear window with suction cups over the
opening, align it with the alignment marks you
made in step 15, and set it down on the adhesive.
Lightly push on the rear window until its edges are
fully seated on the adhesive all the way around.
NOTE: Do not open or close any of the doors for
about an hour until the adhesive is dry.
22. Scrape or wipe the excess adhesive off with a putty
knife or towel. To remove adhesive from a painted
surface or the rear window, use a soft shop towel
dampened with isopropyl alcohol.
23. After the adhesive has dried, spray water over the
rear window and check for leaks. Mark the leaking
area, let the rear window dry, then seal with sealant.
Let the vehicle stand for at least 4 hours after rear
window installation. If the vehicle has to be used
within the first 4 hours, it must be driven slowly.
24. Reinstall all remaining removed parts.
NOTE: Advise the customer not to do the following
things for 2 to 3 days:
• Slam the doors with all the windows rolled up.
• Twist the body excessively (such as when going
in and out of driveways at an angle or driving
over rough, uneven roads).
08/08/21 15:00:15 61SNR030_200_0054
*01
SNR9AB9J34200000000DAAT01
20-53
Moonroof
Component Location Index
BRACKET COVER
FRAME SEAL A
SLIDE STOP
FRONT DRAIN VALVE
REAR DRAIN VALVE
CABLE TUBE
REAR BRACKET A
GLASS
DRAIN CHANNEL
WIND DEFLECTOR
SUNSHADE
CABLE ASSEMBLY
DRAIN CHANNEL SLIDER
REAR DRAIN TUBE
MOTOR
FRAME
FRONT DRAIN TUBE
FRAME SEAL B
SLIDER SPACER
SUNSHADE REAR STOP
SUNSHADE HANDLE
FRONT SUNSHADE
BASE SLIDER
REAR SUNSHADE
BASE SLIDER
REAR HOOK
Position Adjustment, page 20-55
Replacement, page 20-55
Closing Force and Opening Drag Check, page 20-64
Replacement, page 20-57
Replacement, page 20-56
Replacement, page 20-58
Replacement,
page 20-62
Replacement, page 20-62
Replacement,
page 20-60
Replacement,
page 20-59
Replacement, page 20-60
Replacement,
page 20-60
08/08/21 15:00:18 61SNR030_200_0055
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст