Acura CSX. Manual — part 311
*01
SNR9AA1E10411300000MEAT00
14-319
Secondary Shaft Disassembly, Inspection, and Reassembly
CONICAL
SPRING
WASHER
THRUST NEEDLE
BEARING
1ST GEAR
TRANSMISSION
HOUSING BEARING
1ST/3RD CLUTCH
O-RINGS
THRUST WASHER,
40 x 51.5 mm
THRUST NEEDLE BEARING
2ND GEAR
NEEDLE BEARING
THRUST NEEDLE BEARING
IDLER GEAR
THRUST NEEDLE BEARING
SEALING RINGS,
29 mm
SET RING
3RD GEAR
SECONDARY SHAFT
THRUST NEEDLE
BEARING
NEEDLE BEARING
THRUST NEEDLE
BEARING
THRUST WASHER,
37 x 58 mm
O-RINGS
2ND CLUTCH
NEEDLE BEARING
3RD GEAR COLLAR
LOCKNUT (FLANGE NUT)
24 x 1.25 mm
Left-hand threads
1. Inspect the thrust needle bearing and the needle bearing for galling and rough movement.
2. Inspect the splines for excessive wear and damage.
3. Check the shaft bearing surface for scoring and excessive wear.
4. Before installing new O-rings, wrap the shaft splines with tape to prevent O-ring damage.
5. Lubricate all parts with ATF during assembly.
6. Install the conical spring washer and the idler gear in the direction shown.
7. Replace the locknut and the conical spring washer with new ones when assembling the transmission. The locknut
has left-hand threads.
8. Check the clearance of 2nd gear (see page 14-321) and 1st gear (see page 14-322).
Replace.
Replace.
Selective part
Replace.
Replace.
Selective part
Replace.
Replace.
08/08/21 14:51:22 61SNR030_140_0321
01
02
SNR9AA1E10411354203KDAT10
Special Tools Required
Removal
Installation
14-320
Shafts and Clutches
Secondary Shaft Ball Bearing, Idler Gear Removal and Installation
C
A
B
E
D
B
C
A
07QAD-P0A0100
Attachment, 42 mm I.D. 07QAD-P0A0100
Place a spacer (A) on the secondary shaft (B), and set
the puller (C) under the idler gear (D), then remove the
idler gear and the ball bearing (E).
Install the idler gear (A) on the secondary shaft (B), and
install the ball bearing (C) over the idler gear using the
42 mm I.D. attachment and a press.
08/08/21 14:51:23 61SNR030_140_0322
01
02
*01
SNR9AA1E10411354181MAAT00
−
−
Standard: 0.04
0.12 mm (0.002
0.005 in.)
14-321
Secondary Shaft 2nd Gear Axial Clearance Inspection
G
A
B
C
D
E
F
H
C
A
B
C
37 x 58 mm
THRUST WASHER
1. Install the thrust needle bearing (A), the needle
bearing (B), 2nd gear (C), the thrust needle bearing
(D), the 37 x 58 mm thrust washer (E), and the 2nd
clutch (F) on the secondary shaft (G), then secure
them with the set ring (H).
2. Measure the clearance between the snap ring (A)
and the 2nd clutch guide (B) using a feeler gauge
(C), in at least three places. Use the average as the
actual clearance.
08/08/21 14:51:24 61SNR030_140_0323
01
SNR9AA1E10411354171MAAT00
THRUST WASHER, 37 x 58 mm
No.
Part Number
Thickness
Special Tools Required
14-322
14-322
Shafts and Clutches
Secondary Shaft 1st Gear Axial
Clearance Inspection
L
24 x 1.25 mm
29 N·m (3.0 kgf·m, 22 lbf·ft)
K
J
I
G
F
E
D
C
B
A
H
3. If the clearance is out of standard, remove the
37 x 58 mm thrust washer and measure its
thickness.
4. Select and install a new thrust washer, then
recheck.
1
90511-PRP-010
3.900 mm (0.154 in.)
2
90512-PRP-010
3.925 mm (0.155 in.)
3
90513-PRP-010
3.950 mm (0.156 in.)
4
90514-PRP-010
3.975 mm (0.156 in.)
5
90515-PRP-010
4.000 mm (0.157 in.)
6
90516-PRP-010
4.025 mm (0.158 in.)
7
90517-PRP-010
4.050 mm (0.159 in.)
8
90518-PRP-010
4.075 mm (0.160 in.)
9
90519-PRP-010
4.100 mm (0.161 in.)
10
90520-PRP-010
4.125 mm (0.162 in.)
11
90521-PRP-010
4.150 mm (0.163 in.)
12
90522-PRP-010
4.175 mm (0.164 in.)
13
90523-PRP-000
4.200 mm (0.165 in.)
14
90524-PRP-000
4.225 mm (0.166 in.)
15
90525-PRP-000
4.250 mm (0.167 in.)
16
90526-PRP-000
4.275 mm (0.168 in.)
17
90527-PRP-000
4.300 mm (0.169 in.)
18
90528-PRP-000
4.325 mm (0.170 in.)
19
90529-PRP-000
4.350 mm (0.171 in.)
20
90530-PRP-000
4.375 mm (0.172 in.)
5. After replacing the thrust washer, make sure the
clearance is within standard.
6. Disassemble the installed parts from the secondary
shaft.
Attachment, 42 mm I.D. 07QAD-P0A0100
1. Install the thrust needle bearing (A), the needle
bearing (B), 1st gear (C), the thrust needle bearing
(D), the 40 x 51.5 mm thrust washer (E), the 1st/3rd
clutch (F), and the 3rd gear collar (G) on the
secondary shaft (H). Do not install the O-rings
during inspection.
08/08/21 14:51:24 61SNR030_140_0324
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст