Acura CSX. Manual — part 723
04
05
*01
24-208
SRS
A
42 N·m
(4.2 kgf·m, 30 lbf·ft)
07744-0010300
MORE THAN
4 mm (0.2 in.)
A
B
B
B
B
3. Insert the special tool into the hole in the cushion
frame to position the spring washers, then tighten
the TORX nuts (A). Begin with
, and tighten them
in crisscross pattern in two or more steps.
4. Using the pin driver to position the spring washer’s,
torque the TORX nuts in the sequence shown in
two or more steps.
5. Make sure the gap between the spring washer (A)
and the seat track (B) is more than 4 mm (0.2 in.) as
shown.
6. Reassemble the front passenger’s seat cushion
cover/pad (see page 20-127).
7. Reinstall the front passenger’s seat (see page
20-118).
8. Do the battery terminal reconnection procedure
(see page 22-68).
9. Calibrate the ODS unit (see page 24-27).
10. Clear any DTCs (see page 24-23).
11. Confirm proper operation: Turn the ignition switch
to ON (II); the SRS indicator should come on for
about 6 seconds and then go off.
08/08/21 14:02:03 61SNR030_240_0208
01
02
SNR9A00H46400043081KBAT00
Removal
Installation
24-209
ODS Unit Replacement
B
A
C
D
D
C
A
B
NOTE: Review the seat replacement procedure
(see page 20-118) before doing repairs or service.
1. Do the battery terminal disconnection procedure
(see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the passenger’s seat assembly (see page
20-118) and seat-back cover (see page 20-127).
3. Disconnect the ODS unit 18P connector (A) and
OPDS sensor connectors (B) from the ODS unit (C).
4. Remove the two nuts (D) and the ODS unit.
1. Place the ODS unit (A) on the seat-back frame.
Tighten the two nuts (B), and connect the ODS unit
harness 18P connector (C) and OPDS sensor
connectors (D) to the ODS unit.
2. Install the seat-back cover in the reverse order of
removal.
3. Do the battery terminal reconnection procedure
(see page 22-68).
4. Set the seat-back in the normal position, and make
sure there is nothing on the front passenger’s seat.
5. Initialize the ODS unit (see page 24-26).
6. Clear any DTCs (see page 24-23).
7. Confirm proper system operation: Turn the ignition
switch to ON (II); the SRS indicator should come on
for about 6 seconds and then go off.
08/08/21 14:02:03 61SNR030_240_0209
01
02
SNR9A00H46400027195KBAT00
Removal
Installation
24-210
SRS
Front Impact Sensor Replacement
A
B
C
A
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
C
B
1. Do the battery terminal disconnection procedure
(see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the front inner fender (see page 20-171).
3. Remove the washer reservoir (see page 22-234).
4. Remove the intake air resonator:
• K20Z2 engine (see page 11-346)
• K20Z3 engine (see page 11-347)
5. Disconnect the engine compartment wire harness
2P connector (A). Using a TORX T30 bit, remove the
TORX bolt (B), then remove the front impact
sensor (C). Discard the bolt.
1. Install the front impact sensor with a new TORX
bolt (A), then connect the engine compartment wire
harness 2P connector (B) to the front impact sensor
(C).
2. Do the battery terminal reconnection procedure
(see page 22-68).
3. Clear any DTCs (see page 24-23).
4. Confirm proper operation: Turn the ignition switch
to ON (II); the SRS indicator should come on for
about 6 seconds and then go off.
5. Reinstall all removed parts.
Replace.
08/08/21 14:02:04 61SNR030_240_0210
*01
*02
SNR9A00H46400053727KBAT00
Removal
Installation
24-211
Driver’s Seat Position Sensor Replacement
A
B
C
C
A
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
B
NOTE:
• Removal of the driver’s seat position sensor must be
done according Precautions and Procedures
(see page 24-13).
• Do not turn the ignition switch to ON (II), and do not
connect the battery cable while removing the driver’s
seat position sensor.
1. Do the battery terminal disconnection procedure
(see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the driver’s seat assembly (see page
20-118).
3. Disconnect the seat position sensor harness 2P
connector (A) from the driver’s seat position sensor
(B).
4. Using a TORX T30 bit, remove the TORX bolt (C),
then remove the driver’s seat position sensor.
NOTE:
• Be sure to install the harness so it does not pinched
or interfere with other parts.
• Do not turn the ignition switch to ON (II), and do not
connect the battery cable while installing the driver’s
seat position sensor.
• After installing the driver’s seat position sensor,
make sure it is clean. Keep it away from dust.
1. Install the driver’s seat position sensor with a new
TORX bolt (A), then connect the seat position
sensor harness 2P connector (B) to the driver’s seat
position sensor (C).
2. Install the driver’s seat assembly (see page 20-118).
3. Do the battery terminal reconnection procedure
(see page 22-68).
4. Clear any DTCs (see page 24-23).
5. Check the operation of the driver’s seat position
sensor with the HDS (see page 24-29).
Replace.
08/08/21 14:02:11 61SNR030_240_0211
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст