Acura CSX. Manual — part 403
+
01
SNR9AC7K801000R1113FAAT00
+
+
+
+
−
−
−
−
DTC 11-13:
DTC 13-13:
DTC 15-13:
DTC 17-13:
YES
NO
DTC
VSA Modulator-control Unit 37P
Connector Terminal
YES
NO
19-117
DTC Troubleshooting
VSA MODULATOR-CONTROL UNIT 37P CONNECTOR
FR
B (GRN)
RL-GND (PUR)
FR-GND (PNK)
RR
B (LT GRN)
RL
B (YEL)
FL
B (WHT)
RR-GND (BLU)
FL-GND (RED)
Right-front Wheel Speed Sensor
Circuit Malfunction
Left-front Wheel Speed Sensor
Circuit Malfunction
Right-rear Wheel Speed Sensor
Circuit Malfunction
Left-rear Wheel Speed Sensor
Circuit Malfunction
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then turn it to
ON (II) again.
4. Check for DTCs with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. Check for loose terminals between the wheel
speed sensor 2P connector and the VSA modulator-
control unit 37P connector. Refer to intermittent
failures troubleshooting (see page 19-98).
5. Turn the ignition switch to LOCK (0).
6. Disconnect the VSA modulator-control unit 37P
connector (see step 2 on page 19-171).
7. Disconnect the appropriate wheel speed sensor 2P
connector.
8. Check for continuity between the appropriate VSA
modulator-control unit 37P connector wheel speed
sensor
B and GND terminals (see table).
11-13
No. 19
No. 6
13-13
No. 22
No. 11
15-13
No. 9
No. 21
17-13
No. 20
No. 8
Repair short in the wires between the
appropriate wheel speed sensor and the VSA
modulator-control unit.
Go to step 9.
Wire side of female terminals
Is DT C 11-13, 13-13, 15-13, and/ or 17 -13
indicated?
Is ther e continuity?
08/08/21 15:04:57 61SNR030_190_0117
*01
*02
+
+
+
+
+
+
+
+
−
−
−
−
DTC
YES
NO
DTC
YES
NO
VSA Modulator-
control Unit 37P
Connector Terminal
Appropriate Wheel
Speed Sensor 2P
Connector Terminal
VSA Modulator-
control Unit 37P
Connector Terminal
Appropriate Wheel
Speed Sensor 2P
Connector Terminal
19-118
VSA System Components
RR
B (LT GRN)
FL
B (WHT)
FR
B (GRN)
RL
B (YEL)
RR
B
(LT BLU)
FL
B
(WHT)
FR
B
(GRN)
RL
B
(YEL)
LEFT-
REAR
RIGHT-
FRONT
RIGHT-
REAR
LEFT-
FRONT
WHEEL SPEED SENSOR 2P CONNECTOR
VSA MODULATOR-CONTROL UNIT 37P CONNECTOR
FL-GND
(RED)
RR-GND
(GRY)
RL-GND
(RED)
FR-GND
(PNK)
RIGHT-
FRONT
LEFT-
REAR
LEFT-
FRONT
RIGHT-
REAR
WHEEL SPEED SENSOR 2P CONNECTOR
VSA MODULATOR-CONTROL UNIT 37P CONNECTOR
FL-GND (RED)
RR-GND (BLU)
RL-GND (PUR)
FR-GND (PNK)
9. Check for continuity between the appropriate VSA
modulator-control unit 37P connector terminal and
the wheel speed sensor 2P connector terminal (see
table).
11-13
No. 9
Right-front
13-13
No. 22
Left-front
15-13
No. 9
Right-rear
17-13
No. 20
Left-rear
Go to step 10.
Repair open in the wire between the
appropriate wheel speed sensor and the VSA
modulator-control unit.
10. Check for continuity between the appropriate VSA
modulator-control unit 37P connector terminal and
the wheel speed sensor 2P connector terminal (see
table).
11-13
No. 6
Right-front
13-13
No. 11
Left-front
15-13
No. 21
Right-rear
17-13
No. 8
Left-rear
Go to step 11.
Repair open in the wire between the
appropriate wheel speed sensor and the VSA
modulator-control unit.
Wire side of female terminals
Terminal side of female terminals
Wire side of female terminals
Terminal side of female terminals
Is ther e continuity?
Is ther e continuity?
08/08/21 15:04:58 61SNR030_190_0118
04
06
+
+
+
+
+
+
+
+
−
−
−
−
DTC
VSA Modulator-control Unit 37P
Connector Terminal
YES
NO
DTC
VSA Modulator-control Unit 37P
Connector Terminal
YES
NO
19-119
FR
B (GRN)
RL-GND (PUR)
FR-GND (PNK)
RR
B (LT GRN)
FL-GND (RED)
FL
B (WHT)
RR-GND
(BLU)
RL
B (YEL)
VSA MODULATOR-CONTROL UNIT 37P CONNECTOR
FR
B (GRN)
RL-GND (PUR)
FR-GND (PNK)
RR
B (LT GRN)
FL-GND (RED)
FL
B (WHT)
RR-GND
(BLU)
RL
B (YEL)
VSA MODULATOR-CONTROL UNIT 37P CONNECTOR
11. Check for continuity between body ground and the
appropriate VSA modulator-control unit 37P
connector terminals (see table).
11-13
No. 19
No. 6
13-13
No. 22
No. 11
15-13
No. 9
No. 21
17-13
No. 20
No. 8
Repair short to body ground in the wire
between the appropriate wheel speed sensor and
the VSA modulator-control unit.
Go to step 12.
12. Turn the ignition switch to ON (II).
13. Measure the voltage between body ground and the
appropriate VSA modulator-control unit 37P
connector terminals (see table).
11-13
No. 19
No. 6
13-13
No. 22
No. 11
15-13
No. 9
No. 21
17-13
No. 20
No. 8
Repair short to power in the wire between
the appropriate wheel speed sensor and the VSA
modulator-control unit.
Go to step 14.
Wire side of female terminals
Wire side of female terminals
Is ther e continuity?
Is ther e 0.1 V or mor e?
08/08/21 15:04:58 61SNR030_190_0119
SNR9AC7K801000R1211FAAT00
−
−
−
−
YES
NO
YES
NO
DTC 12-11:
DTC 14-11:
DTC 16-11:
DTC 18-11:
19-120
19-120
VSA System Components
14. Turn the ignition switch to LOCK (0).
15. Substitute the appropriate wheel speed sensor with
opposite wheel speed sensor, or with a known-
good wheel speed sensor.
16. Reconnect all connectors.
17. Turn the ignition switch to ON (II).
18. Clear the DTC with the HDS.
19. Turn the ignition switch to LOCK (0), then turn it to
ON (II) again.
20. Check for DTCs with the HDS.
Check for loose terminals in the VSA
modulator-control unit 37P connector. If necessary,
substitute a known-good VSA modulator-control
unit (see page 19-171), and retest.
Replace the original wheel speed sensor
(see page 19-173).
NOTE: These DTCs may be caused by electrical
interference. Check for aftermarket devices installed in
the vehicle when these DTCs are indicated.
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Test-drive the vehicle.
NOTE: Drive the vehicle on the road, not on a lift.
4. Check for DTCs with the HDS.
If DTC 12-12, 14-12, 16-12, or 18-12 is
indicated at the same time, do the DTC 12-12,
14-12, 16-12, or 18-12 troubleshooting first
(see page 19-121). If DTC 12-12, 14-12, 16-12, or
18-12 is not indicated, go to step 5.
If any other DTCs are indicated, go to the
indicated DTCs troubleshooting. If DTCs are not
indicated, there is an intermittent failure, the
system is OK at this time. Check for loose terminals
between the wheel speed sensor 2P connector and
the VSA modulator-control unit 37P connector.
Refer to intermittent failures troubleshooting
(see page 19-98).
Right-front Wheel Speed Sensor
Electrical Noise or Intermittent Interruption
Left-front Wheel Speed Sensor
Electrical Noise or Intermittent Interruption
Right-rear Wheel Speed Sensor
Electrical Noise or Intermittent Interruption
Left-rear Wheel Speed Sensor
Electrical Noise or Intermittent Interruption
Is DT C indicated that is indicated in step 4?
Is DT C 12-11, 14-11, 16-11, and/ or 18-11
indicated?
08/08/21 15:04:58 61SNR030_190_0120
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст