Acura CSX. Manual — part 26
01
SNR9A000000000J0501PAAT00
Ref. No.
Tool Number
Description
Qty
5-2
Engine Assembly
Special Tools
07AAK-SNAA120
Universal Lifting Eyelet
1
#
@
01
*01
03
SNR9A00A18223800000KAAT00
Special Tools Required
5-3
Engine Removal
C
A
B
B
A
B
• Engine hanger adapter VSB02C000015
• Engine support hanger, A and Reds AAR-T1256
• 2006 Civic engine hanger VSB02C000025
• Front subframe adapter VSB02C000016
• Universal lifting eyelet 07AAK-SNAA120
: These special tools are available through Honda
Canada Inc. Technical Tools Department; FAX
866-398-8665/e-mail: ch_technicaltools
ch.honda.
com
NOTE:
• Use fender covers to avoid damaging painted
surfaces.
• To avoid damaging the wire and terminals, unplug
the wiring connectors carefully while holding the
connector portion.
• Mark all wiring and hoses to avoid misconnection.
Also, be sure that they do not contact other wiring or
hoses, or interfere with other parts.
1. Secure the hood in the wide open position (support
rod in the lower hole).
2. Relieve the fuel pressure (see page 11-322).
3. Do the battery removal procedure (see page 22-69).
4. Disconnect the vacuum hose and the breather pipe,
then remove the intake air duct (see step 2 on page
9-3).
5. Remove the air cleaner assembly (see page 11-345).
6. Remove the under-cowl panel (see step 4 on page
20-164).
7. Disconnect the connector (A), and remove the
harness clamps (B), then remove the pipe (C).
8. Disconnect the battery cables (A) from the under-
hood fuse/relay box.
9. Remove the harness clamp (B).
04
*02
06
01
5-4
Engine Assembly
A
B
B
C
A
A
B
10. Remove the engine control module (ECM)/
powertrain control module (PCM) cover (A), then
remove the three bolts (B) securing the ECM/PCM.
11. Disconnect the ECM/PCM connectors (A) and the
engine wire harness connector (B).
12. Remove the harness clamps (C).
13. Remove the under-hood fuse/relay box (A) from the
ECM/PCM bracket (B), then remove the ECM/PCM
bracket.
14. K20Z3 engine: Remove the engine cover.
07
01
09
10
5-5
A
B
A
B
15. Disconnect the evaporative emission (EVAP)
canister hose (A) and the brake booster vacuum
hose (B).
16. Remove the quick-connect fitting cover (A), then
disconnect the fuel feed hose (B) (see page 11-329).
17. M/T model: Remove the shift cables. Do not bend
the cables excessively (see step 7 on page 13-8).
18. M/T model: Remove the clutch slave cylinder, and
the clutch line bracket mounting bolt (see step 5 on
page 13-7).
19. M/T model: Remove the air cleaner bracket.
20. Remove the drive belt (see page 4-31).
21. Remove the idler pulley base (see step 2 on page
4-32).
22. Wait until the engine is cool, then carefully remove
the radiator cap.
23. Raise the vehicle on the lift.
24. Remove the front wheels.
25. Remove the splash shield.
26. Loosen the drain plug in the radiator, and drain the
engine coolant (see page 10-8).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст