Acura CSX. Manual — part 565
01
02
SNR9A00J34300044041FHAT01
01
02
SNR9A00J34300044031FEAT02
Defogger Test
22-307
22-307
Power Mirror Switch Test/
Replacement
Power Mirror Actuator Test
A
Terminal
Position
UP
2
6
13
5
DOWN
LEFT
RIGHT
UP
DOWN
LEFT
RIGHT
L
R
12
11
10
A
B
Position
Terminal
8
7
6
TILT UP
TILT DOWN
SWING LEFT
SWING RIGHT
1. Remove the driver’s door grip cover (see page
20-7).
2. Disconnect the 13P connector from the power
mirror switch (A), then remove the two screws and
power mirror switch.
3. Check for continuity between the terminals in each
switch position according to the table.
4. If the continuity is not as specified, remove the
screws and replace the switch.
5. Install the power mirror switch in the reverse order
of removal.
1. Remove the door panel (see page 20-7).
2. Disconnect the 8P connector (A) from the power
mirror actuator (B).
3. Check actuator operation by connecting power and
ground according to the table.
4. If the mirror fails to work properly, replace the
mirror actuator.
5. Check for continuity between terminals No. 1 and
No. 2 of the 8P connector. These should be
continuity.
6. If the continuity is not as specified, check for:
• An open in the wire.
• A faulty mirror holder.
Wire side of
female terminals
08/08/21 14:36:52 61SNR030_220_0309
01
03
08
*01
SNR9A00J34300044031KBAT00
22-308
Power Mirrors
Power Mirror Actuator Replacement
A
A
A
C
B
A
4.9 N·m
(0.5 kgf·m, 3.6 lbf·ft)
1. Remove the mirror holder (see page 20-34).
2. Remove the power mirror (see page 20-33).
3. Disconnect the 8P connector from the mirror.
4. Record the terminal locations and wire colors.
5. Disassemble the power mirror 8P connector (A),
and remove all terminals from it.
6. Remove the screws and the mirror visor (A).
7. Remove the screw from the gasket (A).
8. Remove the three screws (A), and separate the
mirror housing (B) from the bracket (C).
08/08/21 14:36:53 61SNR030_220_0310
04
05
06
07
Left:
Right:
22-309
A
B
A
B
C
BLU/RED
BLK/WHT
YEL/RED
PUR
YEL/BLK
YEL/WHT
PNK
BLU/RED
BLK/WHT
BLU/GRN
PUR
BLU/BLK
YEL/WHT
PNK
9. Remove the four screws, and the actuator (A).
10. Disconnect the 2P connector (B) from the side turn
signal light.
11. Route the wire harness (A) of the new actuator
through the hole in the bracket (B) and gasket (C).
12. Install the power mirror actuator, bracket, harness
clip, and gasket in the reverse order of removal.
13. Insert the new actuator terminals into the
connector in the original arrangement.
14. Apply tape to seal the intersection of the wire
harness and the gasket.
15. Reassemble in the reverse order of disassembly.
Be careful not to break the mirror when reinstalling
it to the actuator.
16. Reinstall the mirror assembly on the door.
17. Operate the power mirror to ensure smooth
operation.
08/08/21 14:36:53 61SNR030_220_0311
*01
SNR9A00G24166100000DAAT00
22-310
Rear Window Defogger
Component Location Index
REAR WINDOW DEFOGGER RELAY
UNDER-HOOD FUSE/RELAY BOX
REAR WINDOW DEFOGGER
CLIMATE CONTROL UNIT
(Has built-in rear window defogger switch/
mirror defogger switch)
Test, page 22-70
Function Test, page 22-312
Defogger Wire Repair, page 22-313
Replacement, page 21-75
08/08/21 14:36:54 61SNR030_220_0312
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст