Acura CSX. Manual — part 141
01
02
−
−
−
−
YES
NO
YES
NO
11-237
THROTTLE BODY 6P CONNECTOR
TPSB (RED/BLU)
THROTTLE BODY 6P CONNECTOR
VCC3 (BLU)
5. Turn the ignition switch to LOCK (0).
6. Disconnect the throttle body 6P connector.
7. Jump the SCS line with the HDS.
8. Disconnect ECM/PCM connector C (44P).
9. Check for continuity between throttle body 6P
connector terminal No. 3 and body ground.
Repair short in the wire between the throttle
body and the ECM/PCM (C21), then go to step 18.
Go to step 23.
10. Measure the voltage between throttle body 6P
connector terminal No. 2 and body ground.
Go to step 16.
Go to step 11.
11. Turn the ignition switch to LOCK (0).
12. Jump the SCS line with the HDS.
13. Disconnect ECM/PCM connector C (44P).
14. Disconnect the throttle body 6P connector.
Wire side of female terminals
Wire side of female terminals
Is ther e continuity?
Is ther e about 5 V ?
08/08/21 14:23:44 61SNR030_110_0237
03
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
11-238
Electronic Throttle Control System
ECM/PCM CONNECTOR C (44P)
THROTTLE BODY 6P CONNECTOR
VCC3 (BLU)
VCC3 (BLU)
15. Check for continuity between ECM/PCM connector
terminal C12 and throttle body 6P connector
terminal No. 2.
Go to step 23.
Repair open in the wire between the throttle
body and the ECM/PCM (C12), then go to step 18.
16. Turn the ignition switch to LOCK (0).
17. Replace the throttle body; K20Z2 engine (see page
11-348), K20Z3 engine (see page 11-349).
18. Reconnect all connectors.
19. Turn the ignition switch to ON (II).
20. Reset the ECM/PCM with the HDS.
21. Do the ECM/PCM idle learn procedure (see page
11-310).
22. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the throttle body and the ECM/PCM,
then go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
23. Reconnect all connectors.
24. Update the ECM/PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
25. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the throttle body and the ECM/PCM. If
the ECM/PCM was updated, substitute a known-
good ECM/PCM (see page 11-7), then recheck. If the
ECM/PCM was substituted, go to step 1.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-228). If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.
Wire side of
female terminals
Terminal side of female terminals
Is ther e continuity?
Is DT C P0222 indicated?
Is DT C P0222 indicated?
08/08/21 14:23:45 61SNR030_110_0238
01
SNR9AA7K72100090223FAAT30
−
−
−
−
−
−
DTC P0223:
YES
NO
YES
NO
YES
NO
11-239
THROTTLE BODY 6P CONNECTOR
TPSB (RED/BLU)
TP Sensor B Circuit High Voltage
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Check TP SENSOR B in the DATA LIST with the
HDS.
Go to step 4.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the throttle body and the ECM/PCM.
4. Check for Temporary DTCs or DTCs with the HDS.
Go to step 13.
Go to step 5.
5. Turn the ignition switch to LOCK (0).
6. Disconnect the throttle body 6P connector.
7. Turn the ignition switch to ON (II).
8. Measure the voltage between throttle body 6P
connector terminal No. 3 and body ground.
Go to step 18.
Go to step 9.
9. Turn the ignition switch to LOCK (0).
10. Jump the SCS line with the HDS.
11. Disconnect ECM/PCM connector C (44P).
Wire side of female terminals
Is ther e about 4.8 V or mor e?
Ar e DT C P0123 and P0223 indicated at the same
time?
Is ther e about 5 V ?
08/08/21 14:23:45 61SNR030_110_0239
02
03
−
−
−
−
YES
NO
YES
NO
11-240
Electronic Throttle Control System
ECM/PCM CONNECTOR C (44P)
THROTTLE BODY 6P CONNECTOR
TPSB (RED/BLU)
TPSB (RED/BLU)
ECM/PCM CONNECTOR C (44P)
THROTTLE BODY 6P CONNECTOR
SG3 (GRN)
SG3 (GRN)
12. Check for continuity between ECM/PCM connector
terminal C21 and throttle body 6P connector
terminal No. 3.
Go to step 25.
Repair open in the wire between the throttle
body and the ECM/PCM (C21), then go to step 20.
13. Turn the ignition switch to LOCK (0).
14. Disconnect the throttle body 6P connector.
15. Jump the SCS line with the HDS.
16. Disconnect ECM/PCM connector C (44P).
17. Check for continuity between ECM/PCM connector
terminal C39 and throttle body 6P connector
terminal No. 4.
Go to step 25.
Repair open in the wire between the throttle
body and the ECM/PCM (C39), then go to step 20.
Wire side of female terminals
Terminal side of female terminals
Wire side of female terminals
Terminal side of female terminals
Is ther e continuity?
Is ther e continuity?
08/08/21 14:23:45 61SNR030_110_0240
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст