Acura CSX. Manual — part 560
SNR9AB9J34200040651LBAT00
22-287
Resetting the Moonroof Control Unit
Resetting the moonroof is required when any of the following have occurred:
• The moonroof was moved manually while the battery was dead or disconnected.
• The moonroof motor was replaced with a new one.
• Any of components related to the moonroof were replaced.
– Wind deflector
– Moonroof glass
– Moonroof seal
– Moonroof glass bracket
– Moonroof cables, etc.
To reset the moonroof control unit, do these steps:
1. Close the driver’s door, and keep it closed until the procedure is complete.
2. Turn the ignition switch to LOCK (0).
3. Press and hold the tilt switch, and turn the ignition switch to ON (II).
4. Release the tilt switch, and turn the ignition switch to LOCK (0).
5. Repeat steps 3 and 4 four times.
6. Press and hold the moonroof open switch for 3 additional seconds after the moonroof is fully opened.
7. Press and hold the moonroof close switch for 3 additional seconds after the moonroof is fully closed (tilted).
8. Confirm that the moonroof control unit is reset by using the moonroof AUTO OPEN and AUTO CLOSE function.
08/08/21 14:36:04 61SNR030_220_0289
01
SNR9ABCJ34200000000EAAT00
’06-07 models
22-288
Moonroof
Circuit Diagram
No. 24
(20 A)
IGNITION SWITCH
BAT
IG1
WHT
BLU
No. 2 (IG) (50 A)
BATTERY
No. 1 (BAT) (100 A)
(20 A)
D2
G21
E23
K3
K7
YEL
WHT
(CLOSE)
(OPEN)
PUR
PUR
PUR
LT GRN
PUR
5
AUTO
AUTO
MOONROOF CONTROL UNIT
6
10
OPEN
CLOSE
HALL SENSOR
ECM/PCM
4
BLU
GRN
No. 4 (P/W) (40 A)
1
10
7
8
9
7
LT BLU
CPU
MOONROOF SWITCH
BLU
G503
BLK
GRY
5
6
2
9
LT GRN
4
GRN
LIGHT
(LED)
TILT
MOTOR
CLOSE
OPEN
No. 32
UNDER-HOOD FUSE/RELAY BOX
RIGHT REAR
WINDOW MOTOR
No. 14 (7.5 A) FUSE
(UNDER-DASH
FUSE/RELAY BOX)
DASH LIGHTS
BRIGHTNESS
CONTROLLER
UNDER-DASH
FUSE/RELAY BOX
IG1 HOT in ON (II)
and START (III)
H1
K2
08/08/21 14:36:04 61SNR030_220_0290
*01
SNR9ABDJ34200000000EAAT00
’08-09 models
22-289
BLU
No. 4 (P/W) (40 A)
BATTERY
No. 1 (BAT) (100 A)
(20 A)
G2
G21
Q1
K7
YEL
WHT
(CLOSE)
(OPEN)
WHT
PUR
LT GRN
AUTO
AUTO
MOONROOF CONTROL UNIT
6
10
OPEN
CLOSE
HALL SENSOR
ECM/PCM
4
BLU
GRN
1
10
7
8
9
5
LT BLU
CPU
ORN
G503
BLK
GRY
3
4
8
6
LT GRN
2
TILT
MOTOR
CLOSE
OPEN
No. 32
UNDER-HOOD FUSE/RELAY BOX
No. 14 (7.5 A) FUSE
(UNDER-DASH
FUSE/RELAY BOX)
DASH LIGHTS
BRIGHTNESS
CONTROLLER
K2
D4
No. 24 (20 A)
5
POWER
WINDOW
RELAY
MICU
UNDER-DASH FUSE/RELAY BOX
K3
LIGHT
(LED)
(0.84 W)
LIGHT
*1: Except TYPE S models
*2: TYPE model
No. 23 (10 A)
*2
*1
MOONROOF SWITCH
GRN*1
RED*2
08/08/21 14:36:05 61SNR030_220_0291
01
SNR9AB9J34200040651FCAT00
22-290
Moonroof
Moonroof Control Unit Input Test
A
B
WHT
GRN
PUR
LT BLU
LT GRN
YEL
BLK
BLU
NOTE: If the moonroof works OK manually, but will not work in AUTO, or reverses frequently (obstacle detection), do
the moonroof calibration (see page 22-287) before proceeding with the input test.
1. Turn the ignition switch to LOCK (0).
2. Remove the headliner (see page 20-84).
3. Disconnect the 10P connector (A) from the moonroof control unit (B).
4. Inspect the connector and socket terminals to be sure they are all making good contact.
• If the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
• If the terminals look OK, go to step 5.
Wire side of
female terminals
08/08/21 14:36:05 61SNR030_220_0292
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст