Acura CSX. Manual — part 463
01
02
03
SNR9A00J18573426965KBAT20
20-162
Exterior Trim
Front Fender Trim Replacement
Fastener Locations
: Clip
Right, 4
Left, 3
A
B
C
D
A
A
A
NOTE: Take care not to scratch the fender trim or the
body.
1. Remove the clips with a clip remover.
2. Disconnect the washer mouth (A) from the washer
tank (B). Release the hook (C), then remove the
front fender trim (D) and the washer mouth.
3. Install the fender trim in the reverse order of
removal, and note these items:
• Replace the clips (A) with new ones.
• Push the clips into place securely.
08/08/21 15:05:01 61SNR030_200_0164
*01
SNR9A00J18573430211KBAT00
*01
SNR9A00J18500017471KBAT10
20-163
20-163
Front Grille Cover Replacement
Cowl Cover Replacement
A
B
C
D
D
A
A
B
C
Fastener Locations
: Clip, 3
A
: Clip, 2
B
E
E
E
E
B
F
F G
F
F
F
C
H
D
D
H
I
Fastener Locations
: Clip, 3
C
: Clip, 5
F
: Clip, 1
G
(White)
(Light Blue)
C
C
A
D
E
F, G
A
NOTE:
• When prying with a flat-tip screwdriver, wrap it with
protective tape to prevent damage.
• Take care not to scratch the front bumper or the body.
1. Remove the front fender trim from both sides
(see page 20-162).
2. Remove the clips (A, B) by carefully pulling the rear
of the front grille cover (C) up, then remove the
cover by releasing the front edge of the cover from
the front grille (D). Take care not to scratch the
body.
NOTE: To release the clips, pry up on the center pin
at the notch (E).
3. Install the cover in the reverse order of removal,
and note these items:
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the clip portions into place securely.
NOTE: Take care not to scratch the body.
1. Turn the ignition switch to ON (II), then turn on the
wiper switch. When the wiper arms reach about
90 °, quickly turn the ignition switch to LOCK (0).
2. Remove the center cowl cover (A).
–1 Remove the hood rear seal (B) by pu lling it out.
–2 Remove the clips (C).
–3 Release three front hooks (D) from the edge of
the under-cowl panel (E).
–4 Detach the clips (F, G) by carefully pulling the
cover upward, then remove the cover by
releasing the hooks (H). Take care not to
scratch the body.
3. Disconnect the windshield washer tube (I).
08/08/21 15:05:01 61SNR030_200_0165
01
03
20-164
Exterior Trim
Fastener Locations
: Bolt, 5
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
: Bolt, 4
B
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
A
B
C
B
A
A
A
B
B
A
Fastener Location
: Clip, 1
B
A
4. If necessary, remove the bolts (A, B), then remove
the under-cowl panel (C).
5. Remove these items:
• Windshield wiper arms (see page 22-233)
• Front fender trim, both sides (see page 20-162)
6. Detach the clip by carefully pulling the side cowl
cover (A) up, then remove the cover by releasing
the hooks (B) from the front fender. Take care not to
scratch the body. Repeat this step for the other side
cowl cover, and disconnect the windshield washer
tube.
7. Install the parts in the reverse order of removal,
and note these items:
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Make sure the washer tubes are connected
securely.
• Make sure the windshield wipers operate
normally.
• Push the clips into place securely.
08/08/21 15:05:02 61SNR030_200_0166
01
02
SNR9A00J18573451601KBAT00
Special Tools Required
Molding Replacement
20-165
Roof Molding Replacement
A
A
Fastener Location
: Clip
A
Fastener Locations
: Clip (Light Green)
C, F
: Clip (Light Yellow)
G
7 mm
(0.28 in.)
1 mm
(0.039 in.)
D
E
C
F
G
F
A
B
C, F, G
E
C, F, G
D
A
B
B
D
C, F, G
KTC trim tool set SOJATP2014
NOTE:
• Put on gloves to protect your hands.
• Take care not to damage the windshield.
• Do not use any metallic tools to remove the roof
molding, or you may chip or crack the windshield.
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
• Take care not to bend the roof molding.
1. Remove the cowl cover (see page 20-163).
2. Detach the bottom clip (A) at the lower corner of the
windshield.
3. Remove the windshield portion of the roof molding
(A).
–1 Carefully insert a trim tool (B) in under the
molding next to the lower clip (C).
–2 While pulling the clip portion of the molding up
by hand, push the hooks (D) to release the clip
from the retainer (E). Do not pry on the
windshield trim with any tools.
–3 Gradually work your way up to release each of
the clips (F, G).
08/08/21 15:05:03 61SNR030_200_0167
07AAC-SEPA240
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст