Acura CSX. Manual — part 655
SNR9ANGK761000N2702FAAT00
SNR9ANGK761000N2703FAAT02
−
−
−
−
DTC 2702:
DTC 2703:
YES
NO
YES
NO
23-331
23-331
GPS Diag: Receiver in Navi ECU
Aircon Diag
NOTE:
• Check the vehicle battery condition first.
• Before you troubleshoot, make sure to follow the
general troubleshooting information (see page
23-266).
• Make sure the vehicle is parked outside, away from
buildings.
• Check for electronic aftermarket accessories
(possibly hidden) mounted near the GPS antenna or
the navigation unit.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back
to ON (II).
3. Go into the Diagnostic Menu, and Select the Self-
Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
4. Select the System Links, then select the GPS Ant.
Intermittent failure, the system is OK at this
time.
Replace the navigation unit (see page 23-355).
NOTE:
• Check the vehicle battery condition first.
• Check for B-CAN DTCs and resolve them before
troubleshooting.
• Before you troubleshoot, make sure to follow the
general troubleshooting information (see page
23-266).
• DTC 2703 can be stored when the ignition switch is at
ACCESSORY (I). With the ignition switch is in
ACCESSORY (I), the climate control unit is turned off
and the navigation unit loses communication and
stores DTCs. Therefore, there is a possibility that the
system is normal even DTC 2703 is stored. Check
system links (see page 23-297) with the engine
running, and if it shows normal, the system is OK at
this time. If not, do this troubleshooting.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back
to ON (II).
3. Go into the Diagnostic Menu, and Select the Self-
Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
4. Check the System Links.
Go to step 5.
Intermittent failure, the system is OK at this
time.
5. Turn the ignition switch to LOCK (0).
Is Receiver in Navi ECU OK indicated?
Is the Air con icon r ed?
08/08/21 14:17:48 61SNR030_230_0334
*01
*02
*03
−
−
−
−
YES
NO
YES
NO
23-332
Navigation System
NAVIGATION UNIT CONNECTOR D (12P)
AC SI
(YEL)
AC CLK
(BLU)
AC SO
(RED)
JUMPER WIRE
CLIMATE CONTROL UNIT CONNECTOR A (32P)
AC SO (RED)
AC SI (YEL)
AC CLK (BLU)
JUMPER WIRE
NAVIGATION UNIT CONNECTOR D (12P)
AC SI
(YEL)
AC CLK
(BLU)
AC SO
(RED)
6. Disconnect navigation unit connector D (12P).
7. Connect navigation unit connector D (12P)
terminals No. 5, No. 6, and No. 12 with a jumper
wire.
8. Turn the ignition switch to ON (II).
9. Press the RECIRCULATION and OFF buttons.
Replace the navigation unit (see page 23-355).
Go to step 10.
10. Turn the ignition switch to LOCK (0), then
disconnect the jumper wire.
11. Disconnect climate control unit connecter A (32P).
12. Connect climate control unit connector A (32P)
terminals No. 28, No. 29, and No. 30 with a jumper
wire.
13. Check for continuity between navigation unit
connector D (12P) terminals No. 5 and No. 6, then
between terminals No. 5 and No. 12.
Go to step 14.
Repair open in the wire(s) between the
navigation unit and the climate control unit.
14. Disconnect the jumper wire.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Does the RECIRCULAT ION indicator tur n on?
Is ther e continuity?
08/08/21 14:17:48 61SNR030_230_0335
*04
*05
−
−
−
−
YES
NO
From terminal
To terminals
YES
NO
23-333
NAVIGATION UNIT CONNECTOR D (12P)
AC SI
(YEL)
AC CLK
(BLU)
AC SO
(RED)
NAVIGATION UNIT CONNECTOR D (12P)
15. Check for continuity between body ground and
navigation unit connector D (12P) terminals No. 5,
No. 6, and No. 12 individually.
Repair short to body ground in the wire(s)
between the navigation unit and the climate control
unit.
Go to step 16.
16. Check for continuity between the terminal of
navigation unit connector D (12P) according to the
table.
D5 (YEL)
D6 (RED), D12 (BLU)
D6 (RED)
D12 (BLU)
Repair short in the wire(s) between the
navigation unit and climate control unit.
Go to step 17.
Wire side of female terminals
Wire side of female terminals
Ar e ther e continuity?
Is ther e continuity?
08/08/21 14:17:49 61SNR030_230_0336
*06
SNR9ANGK761000N2705FAAT00
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
DTC 2705:
23-334
23-334
Navigation System
NAVIGATION UNIT CONNECTOR D (12P)
AC SI
(YEL)
AC CLK
(BLU)
AC SO
(RED)
17. Turn the ignition switch to ON (II).
18. Measure the voltage between body ground and
navigation unit connector D (12P) terminals No. 5,
No. 6, and No. 12 individually.
Repair short to power in the wire(s) between
the navigation unit and the climate control unit.
Replace the climate control unit (see page
21-75).
NOTE: Before you troubleshoot, make sure to follow the
general troubleshooting information (see page 23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back
to ON (II).
3. Go into the Diagnostic Menu, and Select the Self-
Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
4. Select the System Links.
Go to step 5.
Intermittent failure, the system is OK at this
time.
5. Turn the ignition switch to LOCK (0).
6. Connect the HDS to the DLC (see page 23-359).
7. Clear the DTCs with the HDS.
8. Turn the ignition switch to LOCK (0), and then back
to ON (II).
9. Check for DTCs with the HDS.
Do the HFL DTC troubleshooting.
Go to step 10.
10. Turn the ignition switch to LOCK (0).
11. Disconnect navigation unit connector B (24P).
12. Disconnect the HandsFreeLink control unit 28P
connector.
HFL Diag
Wire side of female terminals
Is ther e voltage above 0.2 V ?
Is the HF L icon r ed?
Ar e ther e any HF L DT Cs indicated?
08/08/21 14:17:49 61SNR030_230_0337
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст