Acura CSX. Manual — part 493
01
02
SNR9A00G10110112025KBAT01
01
SNR9A00G10110112021KBAT02
21-87
21-87
A/C Compressor Thermal Protector
Replacement
A/C Compressor Relief Valve
Replacement
7.4 N·m
(0.8 kgf·m, 5.5 lbf·ft)
A
C
B
B
A
A
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
B
1. Remove the bolt and the holder (A). Disconnect the
field coil connector (B), then remove the thermal
protector (C).
2. Replace the thermal protector (A) with a new one,
and apply silicone sealant (B) to the bottom of the
thermal protector.
3. Install the thermal protector in the reverse order of
removal.
NOTE: If the A/C compressor relief valve released
refrigerant to the atmosphere, determine and correct
the cause of the excessive system pressure, then
replace the relief valve.
1. Recover the refrigerant with a recovery/recycling/
charging station (see page 21-90).
2. Remove the relief valve (A), and the O-ring (B). Plug
the opening to keep foreign matter from entering
the system and the A/C compressor oil from
running out.
3. Clean the mating surfaces.
4. Replace the O-ring with a new one at the relief
valve, and apply a thin coat of refrigerant oil before
installing it.
5. Remove the plug, and install and tighten the relief
valve.
6. Charge the system (see page 21-92).
08/08/21 14:43:48 61SNR030_210_0088
01
02
03
04
SNR9A00G10110200000KBAT80
21-88
Climate Control
A/C Condenser Replacement
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
A
B
C
D
1. Recover the refrigerant with a recovery/recycling/
charging station (see page 21-90).
2. Remove the front grille:
• ’06-08 models (see page 20-160)
• ’09 model (see page 20-161)
3. Remove the bolts, then disconnect the discharge
hose (A) from the A/C condenser.
4. Remove the bolt, then disconnect the receiver line
(A) from the A/C condenser.
5. Remove the bolts and the A/C condenser upper
mount brackets (A).
6. Lift the tab (A) to release the lock, then remove the
outside air temperature sensor (B) from the bracket.
Disconnect the 2P connector (C), then remove the
clip (D).
7. Remove the hood latch (see page 20-181).
08/08/21 14:43:49 61SNR030_210_0089
05
01
SNR9A00G10100050552KBAT25
21-89
21-89
Receiver/Dryer Desiccant
Replacement
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
C
8. Remove the A/C condenser (A) by lifting it up. Be
careful not to damage the radiator and A/C
condenser fins when removing the A/C condenser.
9. Install the A/C condenser in the reverse order of
removal, and note these items:
• If you’re installing a new A/C condenser, add
refrigerant oil (SP-10) (see page 21-7).
• Replace the O-rings with new ones at each fitting,
and apply a thin coat of refrigerant oil before
installing them. Be sure to use the correct O-rings
for HFC-134a (R-134a) to avoid leakage.
• Immediately after using the oil, reinstall the cap
on the container, and seal it to avoid moisture
absorption.
• Do not spill the refrigerant oil on the vehicle; it
may damage the paint; if the refrigerant oil
contacts the paint, wash it off immediately.
• Charge the system (see page 21-92).
• Adjust the hood latch (see page 20-152).
NOTE: Install the receiver/dryer as quickly as possible
to prevent the system from absorbing moisture from
the air.
1. Remove the A/C condenser (see page 21-88).
2. Remove the bolts from the A/C condenser, then
remove the receiver/dryer (A), the bracket (B), and
the O-rings (C).
3. Install the receiver/dryer in the reverse order of
removal. Replace the O-rings with new ones, and
apply a thin coat of refrigerant oil (SP-10) before
installing them. Be sure to use the correct O-rings
for HFC-134a (R-134a) to avoid leakage.
08/08/21 14:43:49 61SNR030_210_0090
05
01
SNR9A00G10100050552KBAT25
21-89
21-89
Receiver/Dryer Desiccant
Replacement
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
C
8. Remove the A/C condenser (A) by lifting it up. Be
careful not to damage the radiator and A/C
condenser fins when removing the A/C condenser.
9. Install the A/C condenser in the reverse order of
removal, and note these items:
• If you’re installing a new A/C condenser, add
refrigerant oil (SP-10) (see page 21-7).
• Replace the O-rings with new ones at each fitting,
and apply a thin coat of refrigerant oil before
installing them. Be sure to use the correct O-rings
for HFC-134a (R-134a) to avoid leakage.
• Immediately after using the oil, reinstall the cap
on the container, and seal it to avoid moisture
absorption.
• Do not spill the refrigerant oil on the vehicle; it
may damage the paint; if the refrigerant oil
contacts the paint, wash it off immediately.
• Charge the system (see page 21-92).
• Adjust the hood latch (see page 20-152).
NOTE: Install the receiver/dryer as quickly as possible
to prevent the system from absorbing moisture from
the air.
1. Remove the A/C condenser (see page 21-88).
2. Remove the bolts from the A/C condenser, then
remove the receiver/dryer (A), the bracket (B), and
the O-rings (C).
3. Install the receiver/dryer in the reverse order of
removal. Replace the O-rings with new ones, and
apply a thin coat of refrigerant oil (SP-10) before
installing them. Be sure to use the correct O-rings
for HFC-134a (R-134a) to avoid leakage.
08/08/21 14:43:49 61SNR030_210_0090
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст