Acura CSX. Manual — part 50
01
02
SNR9AEBA14616700000MAAT01
−
−
K20Z3 engine
Specified Torque
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
6 x 1.0 mm Bolts:
,
,
Camshaft End Play
Standard (New): 0.05
0.20 mm (0.002
0.008 in.)
Service Limit:
0.4 mm (0.02 in.)
6-52
Cylinder Head
NOTE: Do not rotate the camshaft during inspection.
1. Remove the rocker arm assembly (see page 6-44).
2. Put the rocker shaft holders, camshaft, and
camshaft holders on the cylinder head, then tighten
the bolts in sequence to the specified torque.
NOTE: If the engine does not have bolt
, skip it
and continue the torque sequence.
3. Seat the camshaft by pushing it away from the
camshaft pulley end of the cylinder head.
4. Zero the dial indicator against the end of the
camshaft, then push the camshaft back and forth
and read the end play. If the end play is beyond the
service limit, replace the cylinder head and recheck.
If it is still beyond the service limit, replace the
camshaft.
03
04
05
←
←
−
−
−
−
Camshaft-to-Holder Oil Clearance
Standard (New):
No. 1 Journal:
0.030
0.069 mm
(0.001
0.003 in.)
No. 2, 3, 4, 5 Journals:
0.060
0.099 mm
(0.002
0.004 in.)
Service Limit:
0.15 mm (0.006 in.)
Camshaft Total Runout
Standard (New): 0.03 mm (0.001 in.) max.
Service Limit:
0.04 mm (0.002 in.)
Cam Lobe Height Standard (New):
6-53
INTAKE
EXHAUST
PRI
MID SEC
SEC
MID
PRI
C/C
C/C
5. Loosen the camshaft holder bolts two turns at a
time, in a crisscross pattern. Then remove the
camshaft holders from the cylinder head.
6. Lift the camshafts out of the cylinder head, wipe
them clean, then inspect the lift ramps. Replace the
camshaft if any lobes are pitted, scored, or
excessively worn.
7. Clean the camshaft journal surfaces in the cylinder
head, then set the camshafts back in place. Place a
plastigage strip across each journal.
8. Install the camshaft holders, then tighten the bolts
to the specified torque as shown in step 2.
9. Remove the camshaft holders. Measure the widest
portion of plastigage on each journal.
• If the camshaft-to-holder clearance is within the
service limits, go to step 11.
• If the camshaft-to-holder clearance is beyond the
service limit and the camshaft has been replaced,
replace the cylinder head.
• If the camshaft-to-holder clearance is beyond the
service limit and the camshaft has not been
replaced, go to step 10.
10. Check the total runout with the camshaft supported
on V-blocks.
• If the total runout of the camshaft is within the
service limit, replace the cylinder head.
• If the total runout is beyond the service limit,
replace the camshaft and recheck the camshaft-
to-holder oil clearance. If the oil clearance is still
beyond the service limit, replace the cylinder
head.
11. Measure the cam lobe height.
INTAKE
EXHAUST
PRI
32.791 mm
(1.2910 in.)
32.772 mm
(1.2902 in.)
MID
35.534 mm
(1.3990 in.)
34.768 mm
(1.3688 in.)
SEC
32.678 mm
(1.2865 in.)
32.661 mm
(1.2859 in.)
PRI: Primary
MID: Mid
SEC: Secondary
C/C: Cam Chain
01
02
*01
04
SNR9A00A14680200000KAAT00
Special Tools Required
6-54
Cylinder Head
Valve, Spring, and Valve Seal Removal
B
A
07757-PJ1010A
A
Valve spring compressor attachment 07757-PJ1010A
Identify the valves and the valve springs as they are
removed so that each item can be reinstalled in its
original position.
1. Remove the cylinder head (see page 6-38).
2. Remove the rocker arm assembly:
• K20Z2 engine (see page 6-43)
• K20Z3 engine (see page 6-44)
3. Using an appropriate-sized socket (A) and plastic
mallet (B), lightly tap the spring retainer to loosen
the valve cotters.
4. Install the valve spring compressor attachment and
the valve spring compressor. Compress the valve
spring, and remove the valve cotters.
5. Remove the valve spring compressor, the valve
spring compressor attachment, the spring retainer,
the valve spring and the valve.
6. Install the valve guide seal remover (A).
7. Remove the valve seal.
8. Remove the valve spring seat.
01
SNR9A00A14680200000MAAT00
01
SNR9A00A14680263001MAAT02
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
K20Z2 engine
Intake Valve Dimensions
A Standard (New): 34.85
35.15 mm
(1.372
1.384 in.)
B Standard (New): 108.7
109.5 mm
(4.280
4.311 in.)
C Standard (New): 5.475
5.485 mm
(0.2156
0.2159 in.)
C Service Limit:
5.445 mm (0.214 in.)
Exhaust Valve Dimensions
A Standard (New): 29.85
30.15 mm
(1.175
1.187 in.)
B Standard (New): 108.3
109.1 mm
(4.264
4.295 in.)
C Standard (New): 5.450
5.460 mm
(0.2146
0.2150 in.)
C Service Limit:
5.420 mm (0.213 in.)
K20Z3 engine
Intake Valve Dimensions
A Standard (New): 34.85
35.15 mm
(1.372
1.384 in.)
B Standard (New): 108.5
109.1 mm
(4.272
4.295 in.)
C Standard (New): 5.475
5.485 mm
(0.2156
0.2159 in.)
C Service Limit:
5.445 mm (0.214 in.)
Exhaust Valve Dimensions
A Standard (New): 29.85
30.15 mm
(1.175
1.187 in.)
B Standard (New): 108.4
109.0 mm
(4.268
4.291 in.)
C Standard (New): 5.450
5.460 mm
(0.2146
0.2150 in.)
C Service Limit:
5.420 mm (0.213 in.)
Intake Valve Stem-to-Guide Clearance
Standard (New): 0.06
0.11 mm
(0.002
0.004 in.)
Service Limit:
0.16 mm (0.006 in.)
Exhaust Valve Stem-to-Guide Clearance
Standard (New): 0.11
0.16 mm
(0.004
0.006 in.)
Service Limit:
0.22 mm (0.009 in.)
Intake Valve Stem-to-Guide Clearance
Standard (New): 0.030
0.055 mm
(0.0012
0.0022 in.)
Service Limit:
0.08 mm (0.003 in.)
Exhaust Valve Stem-to-Guide Clearance
Standard (New): 0.055
0.080 mm
(0.0022
0.0031 in.)
Service Limit:
0.11 mm (0.004 in.)
6-55
6-55
Valve Inspection
Valve Stem-to-Guide Clearance
Inspection
C
B
A
1. Remove the valves (see page 6-54).
2. Measure the valve in these areas.
1. Remove the valves (see page 6-54).
2. Slide the valve out of its guide about 10 mm
(0.39 in.), then measure the stem-to-guide
clearance with a dial indicator while rocking the
stem in the direction of normal thrust (wobble
method).
• If the measurement exceeds the service limit,
recheck it using a new valve.
• If the measurement is now within the service
limit, reassemble using a new valve.
• If the measurement with a new valve still
exceeds the service limit, go to step 3.
3. Subtract the O.D. of the valve stem, measured with
a micrometer, from the I.D. of the valve guide,
measured with an inside micrometer or ball gauge.
Take the measurements in three places along the
valve stem and three places inside the valve guide.
The difference between the largest guide
measurement and the smallest stem measurement
should not exceed the service limit.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст