Acura CSX. Manual — part 547
01
02
SNR9A0AJ54300065704KBAT00
01
02
SNR9A0JJ54300065704KBAT00
’06-07 models
’08-09 models
22-235
22-235
Wiper Blade Replacement
A
D
B
C
C
A
B
A
B
A
B
1. Lift the wiper arm off the windshield, raising the
driver’s side first, then the passenger’s side.
2. Remove the cover (A), by squeezing the two tabs
and pulling it straight out.
3. Press and hold the tab (B), and slide the wiper
blade (C) toward the tab until it releases from the
wiper arm (D).
4. Find the side of the blade labeled ‘‘LOCK’’ (A), then
pull back the end of the blade and slide out the old
rubber (B).
5. Install a new rubber in the reverse order of removal.
6. Install the wiper blades onto the windshield wiper
arms in the reverse order of removal.
7. Test by turning on the wipers. If the blades slip,
turn off the wipers and seat the attachments more
firmly.
1. Lift the wiper arm off the windshield, raising the
driver’s side first, then the passenger’s side.
2. Pull up the tab (A), and slide the wiper blade (B)
until it releases from the wiper arm (C).
3. Find the blade labeled ‘‘SET’’ (A), then release the
blade from it.
4. Pull back the end of the blade and slide out the old
rubber (B).
5. Install a new rubber in the reverse order of removal.
6. Install the wiper blades onto the windshield wiper
arms in the reverse order of removal.
7. Test by turning on the wipers. If the blades slip,
turn off the wipers and seat the attachments more
firmly.
08/08/21 14:28:50 61SNR030_220_0237
[
]
[ ]
01
SNR9A00J54300065701MBAT00
Wiper arms stop position
Washer nozzle position
22-236
Wipers/Washers
Wiper Arm/Nozzle Adjustment
C
B
A
d
e
b
a
c
e
1. When the wiper arms stop at the automatic stop position, confirm that they are at the standard position.
a:
Position at about 23 mm (0.9 in.) from the top of cowl cover (A)
b:
Position at about 96 mm (3.8 in.)
114 mm (4.5 in.)
from the top of cowl cover (A)
: ’08-09 models
2. When you turn on the washers, confirm 50 % or more of the washer fluid lands within the spray area. If the spray
area is not within the standard positions, adjust the nozzles.
c:
Position at about 192 mm (7.6 in.) from the top of the black ceramic area (B) at the lower windshield
d:
Position at about 192 mm (7.6 in.) from the top of the black ceramic area (B) at the lower windshield
e:
Position at about 250 mm (9.8 in.) from the windshield center line (C)
08/08/21 14:28:50 61SNR030_220_0238
01
SNR9A00J54300065041KBAT00
22-237
Washer Tube Replacement
1. Remove the right inner fender (see page 20-171).
2. Remove the washer nozzles and clips, then remove the tubes.
3. Install the parts in the reverse order of removal. Take care not to pinch the washer tube. Check the windshield
washer operation.
08/08/21 14:28:51 61SNR030_220_0239
*01
*02
SNR9A00J22100000000DAAT00
22-238
Gauges
Component Location Index
OIL PRESSURE SWITCH
ECM/PCM
BRAKE FLUID LEVEL SWITCH
FUEL GAUGE SENDING UNIT
GAUGE CONTROL MODULE
(TACH)
ODOMETER SELECT/RESET SWITCH
DASH LIGHTS BRIGHTNESS CONTROLLER
GAUGE CONTROL MODULE
(SPEEDO)
PARKING BRAKE SWITCH
Test, page 8-9
Test, page 19-11
Test, page 11-340
Self-diagnostic Function,
page 22-241
Input Test, page 22-271
Rewriting the ODO Data and
Transferring Maintenance
Minder Data to a New Gauge
Control Module,
page 22-276
Replacement, page 22-277
Outside Air Temperature
Indicator Calibration, page 22-279
Test/Replacement, page 22-278
Test/Replacement, page 22-278
Input Test, page 22-274
Replacement, page 22-277
Test, page 19-11
08/08/21 14:28:53 61SNR030_220_0240
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст