Acura CSX. Manual — part 689
02
−
−
−
−
YES
NO
YES
NO
24-73
SRS UNIT CONNECTOR B (28P)
8. Read the DTC (see page 24-22).
Go to step 9.
Short to power in the front passenger’s seat
belt tensioner; replace the front passenger’s seat
belt (see page 24-4), then clear the DTC.
9. Turn the ignition switch to LOCK (0). Disconnect the
negative cable from the battery, then wait at least 3
minutes.
10. Disconnect both seat belt buckle tensioner
connectors (see step 8 on page 24-21) and driver’s
seat belt tensioner connector (see step 7 on page
24-21).
11. Disconnect SRS unit connector B (28P) from the
SRS unit (see step 9 on page 24-21).
12. Disconnect the simulator lead from the floor wire
harness.
13. Reconnect the negative cable to the battery.
14. Turn the ignition switch to ON (II).
15. Measure the voltage between body ground and
SRS unit connector B (28P) terminals No. 3 and
No. 4, individually. There should be less than 0.2 V.
Faulty SRS unit or poor connection at SRS
unit connector B (28P) and the SRS unit. Check the
connection; if the connection is OK, replace the
SRS unit (see page 24-203).
Short to power in the floor wire harness;
replace the floor wire harness, then clear the
DTC.
Wire side of female terminals
Is DT C 22-8x indicated?
Is the voltage as specif ied?
08/08/21 13:56:57 61SNR030_240_0073
01
SNR9A00K791000R229XFAAT00
−
−
DTC 22-9x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
24-74
SRS
A
070AZ-SNAA200
07SAZ-TB4011A
Short to Ground in the Front Passenger’s
Seat Belt Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead K 070AZ-SNAA200
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that
the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the
negative cable from the battery, then wait at least 3
minutes.
4. Remove the B-pillar lower trim (see page 20-72),
then disconnect the floor wire harness 4P
connector (A) from the front passenger’s seat belt
tensioner.
5. Connect the SRS inflator simulator (2
connectors) and simulator lead K to the floor wire
harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
Does the SRS indicator stay on, and is DT C 22-9x
indicated?
08/08/21 13:56:57 61SNR030_240_0074
02
−
−
−
−
YES
NO
YES
NO
24-75
SRS UNIT CONNECTOR B (28P)
8. Read the DTC (see page 24-22).
Go to step 9.
Short to ground in the front passenger’s seat
belt tensioner; replace the front passenger’s seat
belt (see page 24-4), then clear the DTC.
9. Turn the ignition switch to LOCK (0). Disconnect the
negative cable from the battery, then wait at least 3
minutes.
10. Disconnect both seat belt buckle tensioner
connectors (see step 8 on page 24-21) and driver’s
seat belt tensioner connector (see step 7 on page
24-21).
11. Disconnect SRS unit connector B (28P) from the
SRS unit (see step 9 on page 24-21).
12. Disconnect the simulator lead from the floor wire
harness.
13. Measure the resistance between body ground and
SRS unit connector B (28P) terminals No. 3 and
No. 4, individually. There should be an open circuit
or at least 1 M
.
Faulty SRS unit or poor connection at SRS
unit connector B (28P) and the SRS unit. Check the
connection; if the connection is OK, replace the
SRS unit (see page 24-203).
Short to ground in the floor wire harness;
replace the floor wire harness, then clear the
DTC.
Wire side of female terminals
Is DT C 22-9x indicated?
Is the r esistance as specif ied?
08/08/21 13:56:57 61SNR030_240_0075
01
SNR9A00K791000R271XFAAT00
−
−
DTC 27-1x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
24-76
SRS
B
A
070AZ-SNAA200
07SAZ-TB4011A
Open in the Driver’s Seat Belt Buckle
Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead K 070AZ-SNAA200
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that
the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the
negative cable from the battery, then wait at least 3
minutes.
4. Disconnect the floor wire harness 4P connector (A)
from the driver’s seat belt buckle tensioner
connector (B).
5. Connect the SRS inflator simulator (2
connectors) and simulator lead K to the floor wire
harness connector.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
Does the SRS indicator stay on, and is DT C 27 -1x
indicated?
08/08/21 13:56:58 61SNR030_240_0076
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст