Acura CSX. Manual — part 384
*02
01
01
SNR9A00D00060845121KBAT00
Removal
Lever Grip
19-41
19-41
Parking Brake Lever Grip and Cover
Replacement
A
B
C
D
A
B
C
D
B
A
C
NOTE:
• The parking brake cables must not be bent or
distorted. This will lead to stiff operation and
premature failure.
• Refer to the Exploded View as needed during this
procedure.
1. Release the parking brake lever fully.
2. Loosen the parking brake cable adjusting nut
(see page 19-8).
3. Remove the parking brake cable clip (A) from the
brake cable (B).
4. Disconnect the parking brake cable from the lever
(C).
5. Remove the parking brake cable mounting
hardware, then remove the cable.
6. Install the parking brake cable in the reverse order
of removal, and note these items:
• Be careful not to bend or distort the cable and
boot (D).
• Make sure the parking brake cable clip is fully
seated on the cable housing.
• Adjust the parking brake (see page 19-8).
1. Remove the center console (see page 20-92).
2. Pull up the parking brake fully (8 to 10 clicks).
3. Start at the front edge (A), peel lever grip away
from lever cap (B). Continue to peel the grip from
the lever to gain access to the hooks (C).
4. Push in both sides of the hook (A) on the lever cap
(B), and remove the lever cap and the pushrod (C)
with the knob (D).
Replace.
Replace.
08/08/21 15:02:10 61SNR030_190_0041
*02
01
01
SNR9A00D00060845121KBAT00
Removal
Lever Grip
19-41
19-41
Parking Brake Lever Grip and Cover
Replacement
A
B
C
D
A
B
C
D
B
A
C
NOTE:
• The parking brake cables must not be bent or
distorted. This will lead to stiff operation and
premature failure.
• Refer to the Exploded View as needed during this
procedure.
1. Release the parking brake lever fully.
2. Loosen the parking brake cable adjusting nut
(see page 19-8).
3. Remove the parking brake cable clip (A) from the
brake cable (B).
4. Disconnect the parking brake cable from the lever
(C).
5. Remove the parking brake cable mounting
hardware, then remove the cable.
6. Install the parking brake cable in the reverse order
of removal, and note these items:
• Be careful not to bend or distort the cable and
boot (D).
• Make sure the parking brake cable clip is fully
seated on the cable housing.
• Adjust the parking brake (see page 19-8).
1. Remove the center console (see page 20-92).
2. Pull up the parking brake fully (8 to 10 clicks).
3. Start at the front edge (A), peel lever grip away
from lever cap (B). Continue to peel the grip from
the lever to gain access to the hooks (C).
4. Push in both sides of the hook (A) on the lever cap
(B), and remove the lever cap and the pushrod (C)
with the knob (D).
Replace.
Replace.
08/08/21 15:02:10 61SNR030_190_0041
03
04
Lever Cover
19-42
Conventional Brake Components
A
A
B
5. Remove the lever grip (A) by sliding it up.
6. Remove the clip (A) on the driver’s side of the
parking brake lever cover (B).
7. Separate the parking brake lever covers, and
remove them.
08/08/21 15:02:10 61SNR030_190_0042
05
06
07
Installation
Lever Cover
Lever Grip
19-43
A
B
D
C
A
A
D
D
A
B
C
1. Install the clip (A) on driver’s side of the parking
brake lever cover (B) to the lever (C).
2. Install the passenger’s side of the parking brake
lever cover (D), and squeeze both sides of the cover
together.
3. Install a new lever grip (A) by sliding it over the
cover.
4. Install a new lever cap (A) on to the lever by
aligning the notch (B) in the cap with the tab (C) on
the lever.
5. With the lever cap and grip in position, push down
on the cap to lock the hooks (D) into place.
08/08/21 15:02:11 61SNR030_190_0043
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст