Acura CSX. Manual — part 373
01
02
03
SNR9A0JB54175159634KBAT00
Removal
18-76
TPMS
Tire Pressure Sensor Replacement
A
C
B
90 °
OUTSIDE
A
B
C
A
B
C
1. Raise the vehicle, and support it with safety stands
in the proper locations (see page 1-11).
2. Remove the wheel with the faulty sensor.
3. Remove the tire valve stem cap and the valve stem
core, to deflate the tire.
4. Remove any balance weights, and then break the
bead loose from the wheel with a commercially
available tire changer (A).
Note these items to avoid damaging the tire
pressure sensor:
• Do the outside of the wheel first.
• Position the wheel as shown so the valve
stem (B) is 90 degrees from the bead
breaker (C) as shown.
• Do not position the bead breaker of the tire
changer too close to the rim.
5. Position the wheel so the tire machine (A) and tire
iron (B) are next to the valve stem (C), and will
move away from it when the machine starts. Then
remove the tire from the wheel.
6. Remove the valve stem nut (A) and the washer (B),
then remove the tire pressure sensor with the valve
stem (C) from the wheel.
NOTE: Check the nut and the washer, If they have
deterioration or damage, replace then with new
ones during reassembly.
08/08/21 14:59:02 61SNR030_180_0076
04
05
Installation
18-77
B
A
A
A
A
7. Remove and discard the valve stem grommet (A)
from the tire pressure sensor (B).
NOTE:
• The valve stem grommet might stay in the wheel;
make sure you remove it.
• Always use a new valve stem grommet
whenever the tire pressure sensor has been
removed from the wheel or when replacing the
tire.
NOTE:
• Use only wheels that have a ‘‘TPMS’’ stamp (A) on
them.
• The vehicle may be equipped with one of the three
types of wheels.
Replace.
08/08/21 14:59:02 61SNR030_180_0077
06
08
18-78
TPMS
A
B
C
D
4 N·m
(0.4 kgf·m, 3 lbf·ft)
F
E
OUT SIDE
WHEEL CENTER
F
E
E
A
B
C
1. Before installing the tire pressure sensor, clean the
mating surfaces on the sensor and the wheel.
2. Install the tire pressure sensor (A) and the washer
(B) to the wheel (C), and tighten the valve stem nut
(D) finger tight. Make sure the pressure sensor is
resting on the wheel.
NOTE: Install the tire pressure sensor so that
sensor housing surface (E) should not exceed
protrusion (F) of wheel to prevent the sensor
housing from being caught on the bead of the tire
when assembling the tire.
3. Tighten the valve stem nut to the specified torque
while holding the tire pressure sensor.
NOTE:
• Do not use air or electric impact tools to tighten a
valve stem nut.
• Do not twist the tire pressure sensor to adjust its
position with the wheel, as this will damage or
deform the valve stem grommet.
4. Lube the tire bead sparingly with a paste-type tire
mounting lubricant, and position the wheel so the
tire machine (A) and tire iron (B) are next to the
valve stem (C) and will move away from it when
the machine starts. Then install the tire onto the
wheel.
5. With a dry air source, inflate the tire to 300 kPa
(3.1 kgf/cm , 44 psi) to seat the tire bead to the rim,
then adjust the tire pressure (see page 18-5), then
install the valve stem cap.
NOTE: Make sure the tire bead is seated on both
sides of the rim uniformly.
6. Check and adjust the wheel balance, then install the
wheels on the vehicle.
7. Remove the jack stands, and lower the vehicle.
Torque the wheel nuts to specification.
8. Connect the HDS, and memorize the tire pressure
sensor IDs using the TPMS sensor initializer tool
(see page 18-52).
2
08/08/21 14:59:02 61SNR030_180_0078
SNR9A000000000J1901ZCAT00
Brakes
Conventional Brake Components
. . . . . ..
. . . . . ..
ABS (Anti-lock Brake System)
Components (’06-07 Models)
. 19-47
. . . . . ..
. . . . . ..
VSA (Vehicle Stability Assist) System
Components (’07-09 Models)
. 19-95
. . . . . . . . . . . . . . . .
. . . . . . . . . .
. . . . . . . .
. . . . . . . . . .
. . . . . . . . . . . . . . . ...
. . . .
. . . . . . . . . . . ...
. . . . ...
. . . . . . . . . . ..
. . . . . . . . . .
. . ..
. . . . . . . . . .
. . . . . . . . ...
. . . . . . . . . .
. . . . . . . . .
. . . . . . . . . . .
. . . . . . . . . . . . . ..
. . . . . . . . . ...
. . ...
. . . . . . . . . . .
. . . . . . . . .
. . . . . . . . . ..
. . . . . . . . . . ...
. . . . . . . . .
. . . . . . . . . . .
. . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . .
. . . . . . . .
. . . . . . . . . .
. . . . . . . . . . . . . . . ...
. . . .
. . . . . . . . . . . ...
. . . . ...
. . . . . . . . . . ..
. . . . . . . . . .
. . ..
. . . . . . . . . .
. . . . . . . . ...
. . . . . . . . . .
. . . . . . . . .
. . . . . . . . . . .
. . . . . . . . . . . . . ..
. . . . . . . . . ...
. . ...
. . . . . . . . . . .
. . . . . . . . .
. . . . . . . . . ..
. . . . . . . . . . ...
. . . . . . . . .
. . . . . . . . . . .
. . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . . .
Special Tools
. 19-2
Component Location Index
. 19-3
Brake System Inspection and Test
. 19-4
Symptom Troubleshooting
. 19-5
Brake Pedal and Brake Pedal Position Switch
Adjustment
. 19-6
Parking Brake Inspection and Adjustment
. 19-7
Brake System Bleeding
. 19-9
Brake System Indicator Circuit Diagram
. 19-10
Parking Brake Switch Test
. 19-11
Brake Fluid Level Switch Test
. 19-11
Front Brake Pad Inspection and Replacement
. 19-12
Front Brake Disc Inspection
. 19-19
Front Brake Disc Replacement
. 19-21
Front Brake Caliper Overhaul
. 19-22
Master Cylinder Replacement
. 19-24
Master Cylinder Inspection
. 19-25
Brake Booster Test
. 19-26
Brake Booster Replacement
. 19-27
Rear Brake Pad Inspection and Replacement
. 19-29
Rear Brake Disc Inspection
. 19-32
Rear Brake Disc Replacement
. 19-34
Rear Brake Caliper Overhaul
. 19-35
Brake Pedal Replacement
. 19-36
Brake Hose and Line Inspection
. 19-37
Brake Hose Replacement
. 19-38
Parking Brake Cable Replacement
. 19-40
Parking Brake Lever Grip and Cover
Replacement
. 19-41
Brake Pedal Cover Replacement
. 19-45
08/08/21 15:00:43 61SNR030_190_0001
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст