Acura CSX. Manual — part 67
01
SNR9AEBA32200043351MAAT01
K20Z3 engine
Torque: 16 N·m (1.6 kgf·m, 12 lbf·ft)
8-14
Engine Lubrication
Oil Jet Inspection
1.2 mm (0.05 in.)
1.2 mm
(0.05 in.)
A
B
1. Remove the oil jet, and inspect it as follows.
• Make sure that a 1.1 mm (0.04 in.) diameter drill
will go through the nozzle hole (A) (1.2 mm
(0.05 in.) diameter).
• Insert the other end of a 1.1 mm (0.04 in.) drill
into the oil intake (1.2 mm (0.05 in.) diameter).
Make sure the check ball (B) moves smoothly and
has a stroke of approximately 4.0 mm (0.16 in.).
• Check the oil jet operation with an air nozzle. It
should take at least 200 kPa (2.0 kgf/cm , 28 psi)
to unseat the check ball.
NOTE: Replace the oil jet assembly if the nozzle is
damaged or bent.
2. Carefully install the oil jet. The mounting torque is
critical.
2
*01
SNR9A00A32200043502LAAT00
+
Exploded View
8-15
Oil Pump Overhaul
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
K20Z2 engine:
8 x 1.25 mm
27 N·m
(2.8 kgf·m, 20 lbf·ft)
UPPER BALANCER
SHAFT HOLDER
DOWEL PINS
BALANCER SHAFT
BEARINGS
REAR BALANCER
SHAFT
FRONT BALANCER
SHAFT
LOWER BALANCER
SHAFT HOLDER
OUTER ROTOR
INNER ROTOR
RELIEF VALVE
SPRING
SEALING BOLT
39 N·m
(4.0 kgf·m, 29 lbf·ft)
OIL PUMP SPROCKET
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
10 x 1.25 mm
44 N·m
(4.5 kgf·m, 33 lbf·ft)
PUMP HOUSING
DOWEL PIN
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
BAFFLE PLATE
K20Z3 engine:
8 x 1.25 mm
28 N·m
(2.9 kgf·m, 21 lbf·ft)
16 °
Apply new engine oil to
the bolt threads.
The valve must slide freely
in housing bore.
Replace the oil pump
as an assembly if scored.
Apply new engine oil to
the bolt threads.
Apply new engine oil to
the bolt threads.
02
03
04
05
Oil Pump Removal
8-16
Engine Lubrication
A
B
A
A
B
1. Turn the crankshaft pulley so its top dead center
(TDC) mark (A) lines up with the pointer (B).
2. Remove the oil pan (see page 7-11).
3. Remove and discard the oil pump chain tensioner.
4. To hold the rear balancer shaft, insert a 6 mm long
pin punch (Snap-on PPC108LA or equivalent) (A)
into the maintenance hole in the lower balancer
shaft holder and through the rear balancer shaft.
5. Loosen the oil pump sprocket mounting bolt.
6. Remove the oil pump sprocket (A), then remove the
oil pump (B).
06
07
08
09
−
−
−
−
−
−
Oil Pump Inspection
Inner Rotor-to-Outer Rotor Radial Clearance
Standard (New): 0.06
0.16 mm (0.002
0.006 in.)
Service Limit:
0.20 mm (0.008 in.)
Pump Housing-to-Rotor Axial Clearance
Standard (New): 0.035
0.070 mm
(0.0014
0.0028 in.)
Service Limit:
0.12 mm (0.005 in.)
Pump Housing-to-Outer Rotor Radial Clearance
Standard (New): 0.15
0.21 mm (0.006
0.008 in.)
Service Limit:
0.23 mm (0.009 in.)
8-17
A
B
B
A
A
B
1. Remove the pump housing.
2. Check the inner-to-outer rotor radial clearance
between the inner rotor (A) and the outer rotor (B).
If the inner-to-outer rotor radial clearance exceeds
the service limit, replace the oil pump.
3. Check the pump housing-to-rotor axial clearance
between the rotor (A) and the pump housing (B). If
the pump housing-to-rotor axial clearance exceeds
the service limit, replace the oil pump.
4. Check the pump housing-to-outer rotor radial
clearance between the outer rotor (A) and the
pump housing (B). If the pump housing-to-outer
rotor radial clearance exceeds the service limit,
replace the oil pump.
5. Inspect both rotors and the pump housing for
scoring or other damage. Replace parts if
necessary.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст