Acura CSX. Manual — part 351
Symptom
Probable cause
17-78
EPS Components
34. Install the steering wheel (see page 17-8).
35. With the tires raised off the ground (vehicle on a
lift), check for the following symptoms by turning
the steering wheel fully to the right and left several
times.
Rubbing sound
coming from the
lower steering
column area.
Steering column joint
is contacting the cover.
Grating sound from
the lower steering
column area, or a
rough feeling during
steering.
Poor engagement of
the pinion shaft
serrations.
Noise from around
the steering wheel
during steering.
Poor engagement of
the SRS cable reel with
the steering wheel, or a
damaged cable reel.
36. Install the air cleaner housing (see page 11-345).
37. Install the under cowl panel and cowl cover
(see page 20-163).
38. Do the battery terminal reconnection procedure
(see page 22-68), and do these tasks:
• Turn the ignition switch to ON (II) and check that
the SRS indicator comes on for about 6 seconds
and then goes off.
• Make sure the horn and turn signal switches
work properly.
• Make sure the steering wheel switches work
properly.
39. After installation, do the following checks:
• Check the steering wheel spoke angle. If steering
spoke angles to the right and left are not equal
(steering wheel and rack are not centered),
correct the engagement of the joint/pinion shaft
splines.
• Set the steering column to the center tilt position,
and to the center telescopic position, then check
the wheel alignment and adjust (see page 18-5).
• Make sure the steering wheel spokes are
centered.
• Start the engine, and let it idle. Turn the steering
wheel from lock-to-lock several times. Check that
the EPS indicator does not come on.
• Do the memorizing for the torque sensor neutral
position (see page 17-22).
08/08/21 14:55:18 61SNR030_170_0079
*01
SNR9A00F18100057145KDAT00
Exploded view
17-79
Rack End Removal and Installation
O-RING
TORQUE SENSOR
CONNECTOR
8 x 1.25 mm
20 N·m
(2.0 kgf·m, 14 lbf·ft)
EPS MOTOR
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
LOCKNUT
RACK GUIDE
DISC WASHER
O-RING
SPRING
GEARBOX MOUNT CUSHION
GEARBOX HOUSING
MOUNT CUSHION
TIE-ROD CLIP
LOCKNUT
14 x 1.5 mm
44 N·m
(4.5 kgf·m, 33 lbf·ft)
BOOT
BOOT BAND
RACK END
93 N·m
(9.5 kgf·m, 69 lbf·ft)
LOCK WASHER
RUBBER STOP
GROUND
TERMINAL
TORQUE SENSOR ASSEMBLY
RACK GUIDE
SCREW
HARNESS BRACKET
Replace.
If the EPS motor is
faulty, replace it.
Replace.
Inspect for damage and deterioration.
Inspect for damage and deterioration.
Inspect for damage and deterioration.
Replace.
Inspect for faulty
movement and damage.
Replace.
Replace.
If the torque sensor is damaged,
replace the steering gearbox
as an assembly.
08/08/21 14:55:19 61SNR030_170_0080
02
03
03
Removal
17-80
EPS Components
B
A
A
E
D
A
B
C
NOTE: Do not allow dust, dirt, or other foreign materials
to enter the steering gearbox.
1. Remove the boot bands (A), and discard them.
Remove the tie-rod clips (B), and pull the boots
away from the ends of the gearbox.
2. Unbend the lock washer (A).
3. Hold the surface sections (A) of the steering rack (B)
with one wrench, and unscrew both rack ends (C)
with another wrench. Be careful not to damage the
rack shaft surface with the wrench.
4. Remove the lock washer (D) and rubber stop (E).
Replace.
Replace.
Replace.
08/08/21 14:55:28 61SNR030_170_0081
04
06
07
Installation
17-81
A
B
C
D
E
93 N·m
(9.5 kgf·m,
69 lbf·ft)
A
B
A
B
(P/N 08798-9013)
1. Install a new rubber stop (A) and a new lock washer
(B). Align the lock washer tabs (C) with the slots (D)
on the rack end (E) while holding the lock washer in
place. Repeat this step for the other side of the rack
shaft.
2. Hold the flat surface sections of the steering rack
with one wrench, and tighten both rack ends with
another wrench. Be careful not to damage the rack
surface with the wrench.
3. Bend the lock washer (A) back against the flat spots
(B) on the rack end ball joint housing.
4. Apply multipurpose grease to the circumference of
the rack end joint housing (A) and lock washer.
5. Apply a light coat of silicone grease (P/N
08798-9013) to the boot fitting grooves (B) on the
rack ends.
NOTE: Make sure not to get any silicone grease on
the terminal part of the connectors and switches,
especially if you have silicone grease on your
hands or gloves.
Replace.
Replace.
08/08/21 14:55:28 61SNR030_170_0082
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст