Acura CSX. Manual — part 298
*03
*02
−
−
YES
NO
14-272
A/T Gear Position Indicator
CABLE REEL 20P CONNECTOR
SUPP (BLU)
JUMPER WIRE
PCM CONNECTOR B (44P)
SUPP (BLU/YEL)
10. Turn the ignition switch to LOCK (0).
11. Jump the SCS line with the HDS.
12. Disconnect PCM connector B (44P).
13. Connect cable reel 20P connector terminal No. 16
and body ground with a jumper wire.
14. Check for continuity between PCM connector
terminal B16 and body ground.
Check for poor connections or loose
terminals between cable reel 20P connector
terminal No. 16 and PCM connector terminal B16. If
the connection is OK, update the PCM if it does not
have the latest software (see page 11-227), or
substitute a known-good PCM (see page 11-7), then
recheck. If the symptom goes away with a known-
good PCM, replace the original PCM (see page
11-228).
Repair open in the wire between PCM
connector terminal B16 and the cable reel 20P
connector.
Wire side of female terminals
Terminal side of female terminals
Is ther e continuity?
08/08/21 14:50:00 61SNR030_140_0274
−
−
−
−
−
*04
02
09
SNR9AA1E10410744852FAAT10
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
14-273
Paddle Shifter - (Downshift Switch) Circuit Troubleshooting
GND (LT GRN)
SDNP (BLK/WHT)
CABLE REEL SUBHARNESS 20P CONNECTOR
PADDLE SHIFTER
(DOWNSHIFT SWITCH) CONNECTOR
GND (BLK)
CABLE REEL 20P CONNECTOR
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repair or service.
1. Remove the steering wheel (see page 17-6).
2. Check for continuity between cable reel subharness
20P connector terminals No. 7 and No. 17 when
pressing the paddle shifter
(downshift switch)
and when the switch is released.
Go to step 5.
Go to step 3.
3. Disconnect the paddle shifter
(downshift switch)
connector.
4. Check for continuity between the paddle shifter
(downshift switch) connector terminals when
pressing the switch and when the switch is
released.
Replace the steering switch harness
(see page 17-7).
Replace the paddle shifter
(downshift
switch) (see page 14-277).
5. Remove the cable reel (see page 24-200).
6. Check for continuity between cable reel 20P
connector terminal No. 6 and body ground.
Go to step 7.
Repair open in the wire between cable reel
20P connector terminal No. 6 and body ground
(G504), or repair poor body ground (G504).
Wire side of female terminals
Terminal side of male terminals
Wire side of female terminals
Is ther e continuity when pr essing the paddle
shif ter
( downshif t switch) and no continuity
when the switch r eleased?
Is ther e continuity when pr essing the switch and
no continuity when the switch r eleased?
Is ther e continuity?
08/08/21 14:50:00 61SNR030_140_0275
−
10
11
−
−
−
−
YES
NO
YES
NO
14-274
A/T Gear Position Indicator
SDNP (GRN)
CABLE REEL 20P CONNECTOR
SDNP (GRN)
CABLE REEL 20P CONNECTOR
GND (BLK)
7. Check for continuity between cable reel 20P
connector terminal No. 17 and body ground.
Repair short to body ground in the wire
between cable reel 20P connector terminal No. 17
and PCM connector terminal D15.
Go to step 8.
8. Turn the ignition switch to ON (II), and shift to S.
9. Measure the voltage between cable reel 20P
connector terminals No. 6 and No. 17.
Replace the cable reel (see page 24-200).
Go to step 10.
Wire side of female terminals
Wire side of female terminals
Is ther e continuity?
Is ther e about 5 V in neutr al position and no
voltage when pr essing the paddle shif ter
( downshif t switch)?
08/08/21 14:50:01 61SNR030_140_0276
*05
*06
−
−
YES
NO
14-275
CABLE REEL 20P CONNECTOR
SDNP (GRN)
JUMPER WIRE
PCM CONNECTOR B (44P)
SDNP (BRN)
10. Turn the ignition switch to LOCK (0).
11. Jump the SCS line with the HDS.
12. Disconnect PCM connector B (44P).
13. Connect cable reel 20P connector terminal No. 17
and body ground with a jumper wire.
14. Check for continuity between PCM connector
terminal B40 and body ground.
Check for poor connections or loose
terminals between cable reel 20P connector
terminal No. 17 and PCM connector terminal B40. If
the connection is OK, update the PCM if it does not
have the latest software (see page 11-227), or
subsitute a known-good PCM (see page 11-7), then
recheck. If the symptom goes away with a known-
good PCM, replace the original PCM (see page
11-228).
Repair open in the wire between PCM
connector terminal B40 and the cable reel 20P
connector.
Wire side of female terminals
Terminal side of female terminals
Is ther e continuity?
08/08/21 14:50:01 61SNR030_140_0277
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст