Acura CSX. Manual — part 440
39
40
20-81
Fastener Locations
: Clip, 3
A
: Clip, 2
B
A
B
C
D
E
C
A
A
B
A
6. Remove the clips (A, B), then remove the trunk side
trim panel (C). Release the wire harness (D) from
the slit (E) in the trim panel.
7. If necessary, remove the trunk tool box (A).
8. Install the trim in the reverse order of removal, and
note these items:
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the clips into place securely.
08/08/21 15:01:37 61SNR030_200_0083
41
42
SNR9A00J26273400000KDAT53
01
02
SNR9A00J26200030190KDAT00
Special Tools Required
Special Tools Required
20-82
20-82
Interior Trim
Trim Removal/Installation - Trunk
Lid
Grab Handle Removal/Installation
Fastener Locations
: Clip, 2
A
Fastener Locations
: Clip, 4
A
: Clip, 4
B
A
B
C
A
A
A
B
B
B
A
B
A
A
C
B
C
A
KTC trim tool set SOJATP2014
NOTE:
• Put on gloves to protect your hands.
• Take care not to bend or scratch the trim and panels.
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
1. Remove the clips from both trunk lid hinge cover
(A), then remove the covers.
2. Remove the clips (A, B), then remove the trunk lid
trim (C).
3. Install the trim in the reverse order of removal, and
if the clips are damaged or stress-whitened, replace
them with new ones.
KTC trim tool set SOJATP2014
NOTE: Use the appropriate tool from the KTC trim tool
set to avoid damage when removing components.
1. Lower the grab handle (A), then pull out the
stoppers (B).
2. While pinching the clips (A), release the hooks (B),
then remove the grab handle (C).
08/08/21 15:01:38 61SNR030_200_0084
07AAC-SEPA240
07AAC-SEPA240
03
04
05
06
20-83
A
A
B
A
B
C
A
B
C
A
3. Remove all of the clips (A) with a pair of pliers by
pinching its hooks.
4. If the side curtain airbag has deployed, replace the
grab handle with a new one.
5. If the side curtain airbag has not deployed, to
prevent the side curtain airbags from deploying
improperly and possibly causing injury, inspect the
removed pieces and replace them if they have any
of the following damage:
• Any cracks or breakage in the grab handle (A).
• Any cracks or stress-whitening in the stoppers (B).
6. Install the clips (A) to the grab handle (B), then
install the stoppers (C) fully into the clips.
7. Position the grab handle (A) on the bracket (B), and
push on the grab handle until the clips (C) snap into
place securely.
08/08/21 15:01:39 61SNR030_200_0085
01
02
*01
SNR9A00J26200031201KDAT00
Special Tools Required
20-84
Interior Trim
Headliner Removal/Installation
A
B
C
A
B
Fastener Locations
: TORX Screw, 2
A
B
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
SRS component locations, (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:
• Put on gloves to protect your hands.
• Take care not to bend or scratch the trim and panels.
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
1. Do the battery terminal disconnection procedure
(see page 22-68), and wait at least 3 minutes before
beginning work.
2. Remove these items:
• A-pillar trim, both sides (see page 20-69)
• Ceiling light (see page 22-197)
• Front seat belt upper anchor, both sides (see step
6 on page 24-4)
• B-pillar lower trim, both sides (see page 20-72)
• B-pillar upper trim, both sides (see page 20-72)
• C-pillar trim, both sides (see page 20-75)
• Grab handles, four places (see page 20-82)
3. Release the tabs (A) from the bracket (B) of the
sunvisor cap (C) with a trim tool.
4. Remove the sunvisor cap (A) from the bracket (B).
5. From both sides, remove the sunvisor (A).
–1 Remove the sunvisor from the body and the
holder (B).
–2 Remove the screws with a TORX T25 bit.
–3 Remove the sunvisor from the body, and if
equipped disconnect the vanity mirror light
connector.
08/08/21 15:01:39 61SNR030_200_0086
07AAC-SEPA240
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст