Acura CSX. Manual — part 256
07
05
06
08
−
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
YES
NO
14-105
INPUT SHAFT (MAINSHAFT)
SPEED SENSOR CONNECTOR
NM (WHT/RED)
SG2 (GRN/BLK)
INPUT SHAFT (MAINSHAFT)
SPEED SENSOR CONNECTOR
NM (WHT/RED)
INPUT SHAFT
(MAINSHAFT)
SPEED SENSOR
CONNECTOR
SG2 (GRN/BLK)
PCM CONNECTOR B (44P)
SG2 (GRN/BLK)
INPUT SHAFT
(MAINSHAFT)
SPEED SENSOR
CONNECTOR
PCM CONNECTOR B (44P)
NM (WHT/RED)
NM
(WHT/RED)
19. Measure the voltage between input shaft
(mainshaft) speed sensor connector terminals
No. 2 and No. 3.
Replace the input shaft (mainshaft) speed
sensor (see page 14-227), then go to step 26.
Go to step 20.
20. Turn the ignition switch to LOCK (0).
21. Jump the SCS line with the HDS.
22. Disconnect PCM connector B (44P).
23. Check for continuity between input shaft
(mainshaft) speed sensor connector terminal No. 2
and body ground.
Repair short to body ground in the wire
between PCM connector terminal B17 and the input
shaft (mainshaft) speed sensor, then go to step 26.
Go to step 24.
24. Check for continuity between PCM connector
terminal B33 and input shaft (mainshaft) speed
sensor connector terminal No. 3.
Go to step 25.
Repair open in the wire between PCM
connector terminal B33 and the input shaft
(mainshaft) speed sensor, then go to step 26.
25. Check for continuity between PCM connector
terminal B17 and input shaft (mainshaft) speed
sensor connector terminal No. 2.
Go to step 32.
Repair open in the wire between PCM
connector terminal B17 and the input shaft
(mainshaft) speed sensor, then go to step 26.
Wire side of female terminals
Wire side of female terminals
Wire side of
female terminals
Terminal side of
female terminals
Wire side of
female terminals
Terminal side of
female terminals
Is ther e about 5 V ?
Is ther e continuity?
Is ther e continuity?
Is ther e continuity?
08/08/21 14:41:05 61SNR030_140_0107
−
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
YES
NO
14-106
Automatic Transmission
26. Reconnect all connectors.
27. Turn the ignition switch to ON (II).
28. Clear the DTC with the HDS.
29. Start the engine, run the vehicle with the shift lever
in D, and keep the vehicle at speeds over 20 km/h
(12 mph) for at least 10 seconds. Slow down and
stop the wheels.
30. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the input shaft (mainshaft)
speed sensor and the PCM, then go to step 1.
Go to step 31.
31. Monitor the OBD STATUS for P0716 or P0717 in the
DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 30,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the input
shaft (mainshaft) speed sensor and the PCM, then
go to step 1. If the HDS indicates NOT COMPLETED,
go to step 29.
32. Reconnect all connectors.
33. Update the PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
34. Start the engine, run the vehicle with the shift lever
in D, and keep the vehicle at speeds over 20 km/h
(12 mph) for at least 10 seconds. Slow down and
stop the wheels.
35. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the input shaft (mainshaft)
speed sensor and the PCM. If the PCM was updated,
substitute a known-good PCM (see page 11-7), then
go to step 34. If the PCM was substituted, go to step
1.
Go to step 36.
36. Monitor the OBD STATUS for P0716 or P0717 in the
DTCs MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 35,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the input
shaft (mainshaft) speed sensor and the PCM. If the
PCM was updated, substitute a known-good PCM
(see page 11-7), then go to step 34. If the PCM was
substituted, go to step 1. If the HDS indicates NOT
COMPLETED, go to step 34.
Is DT C P07 16 or P07 17 indicated?
Does the HDS indicate PASSED?
Is DT C P07 16 or P07 17 indicated?
Does the HDS indicate PASSED?
08/08/21 14:41:06 61SNR030_140_0108
01
SNR9AA1K77100090718FAAT00
−
−
−
−
−
−
DTC P0718:
YES
NO
YES
NO
YES
NO
14-107
PCM CONNECTOR C (44P)
LG2 (BRN/YEL)
LG1 (BRN/YEL)
Input Shaft (Mainshaft) Speed
Sensor Intermittent Failure
NOTE:
• Before you troubleshoot, record all freeze data and
any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
• This code is caused by an electrical circuit problem
and cannot be caused by a mechanical problem in the
transmission.
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Test-drive the vehicle with the shift lever in D at
speeds over 20 km/h (12 mph), and let the
transmission shift through all five gears.
4. Monitor the OBD STATUS for P0718 in the DTCs
MENU with the HDS.
Go to step 5.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. Check for
poor connections or loose terminals between the
input shaft (mainshaft) speed sensor and the PCM.
If the HDS indicates NOT COMPLETED, go to step 3.
5. Turn the ignition switch to LOCK (0).
6. Disconnect the input shaft (mainshaft) speed
sensor connector, and inspect the connector and
the connector terminals to be sure they are making
good contact.
Go to step 7.
Repair the connector terminals, then go to
step 23.
7. Jump the SCS line with the HDS.
8. Disconnect PCM connector C (44P).
9. Check for continuity between PCM connector
terminal C40 and body ground, and between PCM
connector terminal C44 and body ground.
Go to step 10.
Repair open in the wires between PCM
connector terminals C40, C44, and body ground
(G101) (see page 22-16), or repair poor body
ground (G101), then go to step 23.
10. Connect PCM connector C (44P).
11. Turn the ignition switch to ON (II).
Terminal side of female terminals
Does the HDS indicate F AILED?
Ar e the connector ter minals OK ?
Is ther e continuity?
08/08/21 14:41:06 61SNR030_140_0109
02
*01
*02
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
14-108
Automatic Transmission
INPUT SHAFT (MAINSHAFT)
SPEED SENSOR CONNECTOR
VCC2 (YEL/BLU)
INPUT SHAFT (MAINSHAFT)
SPEED SENSOR CONNECTOR
NM (WHT/RED)
INPUT SHAFT (MAINSHAFT)
SPEED SENSOR CONNECTOR
NM (WHT/RED)
12. Measure the voltage between input shaft
(mainshaft) speed sensor connector terminal No. 1
and body ground.
Go to step 13.
Go to step 19.
13. Measure the voltage between input shaft
(mainshaft) speed sensor connector terminal No. 2
and body ground.
Replace the input shaft (mainshaft) speed
sensor (see page 14-227), then go to step 23.
Go to step 14.
14. Turn the ignition switch to LOCK (0).
15. Jump the SCS line with the HDS.
16. Disconnect PCM connector B (44P).
17. Check for continuity between input shaft
(mainshaft) speed sensor connector terminal No. 2
and body ground.
Repair short to body ground in the wire
between PCM connector terminal B17 and the input
shaft (mainshaft) speed sensor, then go to step 23.
Go to step 18.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is ther e about 5 V ?
Is ther e about 5 V ?
Is ther e continuity?
08/08/21 14:41:06 61SNR030_140_0110
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст