Acura CSX. Manual — part 360
13
*01
03
16
Installation
18-27
FRONT
A
B
C
A
’06-08 models except Type S model:
10 x 1.25 mm
44 N·m (4.5 kgf·m, 33 lbf·ft)
’06-08 models type S model:
10 x 1.25 mm
59 N·m (6.0 kgf·m, 43 lbf·ft)
’09 model:
10 x 1.25 mm
59 N·m (6.0 kgf·m, 43 lbf·ft)
A
14 x 1.5 mm
90 N·m
(9.2 kgf·m,
67 lbf·ft)
C
B
A
B
C
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
1. Install the damper/spring (A) onto the frame. Note
the direction of the damper mounting base as
shown.
NOTE: Be careful not to damage the body.
2. Loosely install the new flange nuts (A).
NOTE: Install the service cap (B) and the lid (C) after
tightening the flange nuts to the specified torque
value.
3. Loosely install the new damper pinch bolts (A) and
the new self-locking nuts (B) to the damper (C).
4. Raise the front suspension with a floor jack to load
the suspension with the vehicle’s weight.
5. Tighten the flange nuts on top of the damper to the
specified torque value.
6. Tighten the damper pinch bolts to the specified
torque value.
7. Install the wheel speed sensor harness clip (A) and
the brake hose bracket (B) to the damper (C).
8. Install the service cap and the lid.
9. Clean the mating surfaces of the brake disc and the
inside of the wheel, then install the front wheel.
10. Check the wheel alignment, and adjust it if
necessary (see page 18-5).
11. Turn the ignition switch to ON (II), then turn the
windshield wipers to the default positions, and turn
the ignition switch to LOCK (0).
Replace.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:57:39 61SNR030_180_0027
*01
SNR9A00B20200019101MEAT00
Exploded View
18-28
Front Suspension
Damper/Spring Disassembly, Inspection, and Reassembly
DAMPER MOUNTING BEARING
BUMP STOP
DAMPER UNIT
CAP
SELF-LOCKING NUT
12 x 1.25 mm
44 N·m
(4.5 kgf·m, 33 lbf·ft)
UPPER SPRING MOUNTING CUSHION
DAMPER SPRING
DAMPER MOUNTING BASE
LOWER SPRING SEAT
Check for any play or roughness.
Check for weakness,
oil contamination, and damage.
Check for oil leaks, gas leaks,
and smooth operation.
Replace.
Check for deterioration and damage.
Check for damage.
Check for deterioration and damage.
08/08/21 14:57:39 61SNR030_180_0028
06
*02
08
Special Tools Required
Disassembly
Inspection
18-29
A
A
12 x 1.25 mm
07AAA-SVAA100
B
Strut nut adapter 07AAA-SVAA100
NOTE: When compressing the damper spring, use a
commercially available strut spring compressor
(Branick MST-580A or Model 7200, or equivalent)
according to the manufacturer’s instructions.
1. Remove the cap (A) from the top of the damper.
2. Compress the damper spring, then remove the self-
locking nut (A) using the strut nut adapter, a ratchet
or breaker bar while holding the damper shaft with
a hex wrench (B). Do not compress the spring more
than necessary to remove the nut.
3. Release the pressure from the strut spring
compressor, then disassemble the damper as
shown in the Exploded View.
1. Reassemble the damper mounting base and the
self-locking nut.
2. Compress the damper assembly by hand, and
check for smooth operation through a full stroke,
both compression and extension. The damper
should extend smoothly and constantly when
compression is released. If it does not, the gas is
leaking, and the damper should be replaced.
3. Check for oil leaks, abnormal noises, or binding
during these tests.
Replace.
08/08/21 14:57:40 61SNR030_180_0029
△
02
10
*03
04
±
Reassembly
18-30
Front Suspension
A
B
C
D
A
B
C
FRONT
FRONT
44 °24 ’
3 °
A
C
B
D
C
A
Left
Right
A
12 x 1.25 mm
44 N·m (4.5 kgf·m, 33 lbf·ft)
C
07AAA-SVAA100
B
1. Install the damper spring (A) on the upper spring
mounting cushion (B) by aligning the upper end (C)
of the damper spring with the ledge portion (D) of
the upper spring mounting cushion.
2. Compress the damper spring.
3. Install all the parts except the self-locking nut and
the cap onto the damper unit (A) by referring to the
Exploded View.
4. Align the bottom of the spring (B) and the stepped
part of the lower spring seat (C) on the damper unit.
5. Align the damper bracket (A) and the damper
mounting base (B) so that the ‘‘
’’ stamp (C) points
toward the front.
6. Align the angle of the stud bolt (D) on the damper
bracket as shown.
7. Install the new self-locking nut (A).
8. Hold the damper shaft using a hex wrench (B), and
tighten the self-locking nut using the strut nut
adapter (C) and a torque wrench to the specified
torque value.
9. Remove the damper/spring from the strut spring
compressor.
10. Install the cap.
Replace.
08/08/21 14:57:40 61SNR030_180_0030
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст