Acura CSX. Manual — part 718
*01
02
01
*02
SNR9A00H46400012802KBAT00
Removal
Installation
24-188
SRS
Driver’s Airbag Replacement
A
B
A
B
C
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
B
A
B
NOTE: If replacing the driver’s airbag after deployment,
refer to Component Replacement/Inspection After
Deployment (see page 24-185) for a complete list of
other parts that must also be replaced.
1. Do the battery terminal disconnection procedure
(see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the access panel (A) from the steering
wheel, then disconnect the driver’s airbag 4P
connector (B) from the cable reel.
3. Using a TORX T30 bit, remove the two TORX bolts
(A) and discard them.
4. Disconnect the horn switch connector (1P), then
remove the driver’s airbag (B).
1. Connect the horn switch connector (1P) (A) to the
driver’s airbag.
2. Place the driver’s airbag (B) in the steering wheel,
and secure it with new TORX bolts (C).
3. Connect the driver’s airbag 4P connector (A) to the
cable reel 4P connector, then install the access
panel (B) on the steering wheel.
4. Do the battery terminal reconnection procedure
(see page 22-68).
5. Clear any DTCs (see page 24-23).
6. After installing the airbag, confirm proper system
operation:
• Turn the ignition switch to ON (II); the SRS
indicator should come on for about 6 seconds
and then go off.
• Make sure the horn works.
Replace.
08/08/21 14:01:55 61SNR030_240_0188
01
02
03
SNR9A00H46400012803KBAT00
Removal
24-189
Front Passenger’s Airbag Replacement
A
A
B
C
C
NOTE: If replacing the front passenger’s airbag after
deployment, refer to Component Replacement/
Inspection After Deployment (see page 24-185) for a
complete list of other parts that must also be replaced.
1. Do the battery terminal disconnection procedure
(see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the glove box (see page 20-104).
3. Disconnect the front passenger’s airbag 4P
connector (A) from the dashboard wire harness.
4. Remove the center panel:
• Navigation unit, with navigation system.
– ’06-08 models (see page 23-256)
– ’09 model (see page 23-355)
• Audio unit, without navigation system.
– ’06-08 models (see page 23-80)
– ’09 model (see page 23-155)
5. Remove the three mounting nuts (A) from the
bracket. Cover the front passenger’s lid and
dashboard with a cloth, and pry carefully with a
screwdriver to lift the front passenger’s airbag
assembly (B) out of the dashboard. If you replacing
only the front passenger’s lid, go to step 6.
NOTE: The front passenger’s lid has pawls (C) on
each side which attach it to the dashboard.
08/08/21 14:01:55 61SNR030_240_0189
01
02
04
05
Installation
24-190
SRS
A
A
B
A
B
B
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
A
6. Cut the four parts (A) of the front passenger’s lid (B)
as shown, and remove the front passenger’s airbag.
NOTE:
• Always replace the front passenger’s lid
whenever you remove the front passenger’s
airbag from the lid.
• Replace the front passenger’s airbag if the airbag
mounting hooks or its housing is damaged.
7. Insert the hooks (A) of the front passenger’s airbag
housing into the new front passenger’s lid, then
insert the other hooks (B) into the lid.
NOTE:
• Make sure there are no objects between the
airbag and the front passenger’s lid.
• Make sure the airbag is fully seated, and make
sure the front passenger’s lid is not deformed or
damaged after the airbag is in place.
• Do not use tools when detaching the front
passenger’s airbag in order to protect it.
1. Place the front passenger’s airbag assembly (A)
into the dashboard. Tighten the front passenger’s
airbag mounting nuts (B).
2. Connect the front passenger’s airbag 4P connector
(A) to dashboard wire harness, then reinstall the
glove box and center panel.
3. Do the battery terminal reconnection procedure
(see page 22-68).
4. Clear any DTC (see page 24-23).
5. After installing the airbag, confirm proper system
operation: Turn the ignition switch to ON (II); the
SRS indicator should come on for about 6 seconds
and then go off.
08/08/21 14:01:56 61SNR030_240_0190
01
*01
SNR9A00H46400055381KBAT00
Removal
Installation
24-191
Side Airbag Replacement
A
B
A
B
6.3 N·m
(0.64 kgf·m, 4.65 lbf·ft)
NOTE: If replacing the side airbag after deployment,
refer to Component Replacement/Inspection After
Deployment (see page 24-185) for a complete list of
other parts that must also be replaced.
1. Do the battery terminal disconnection procedure
(see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the seat assembly (see page 20-118) and
seat-back cover (see page 20-123).
3. Remove the mounting screws (A) and the side
airbag (B).
NOTE:
• If the side airbag lid is secured by tape, remove the
tape.
• Do not open the lid of the side airbag cover.
• Use new mounting screws tightened to the specified
torque. When you replace a side airbag, make sure
that the seat-back cover is installed properly.
Improper installation may prevent proper
deployment.
• Be sure to install the harness wires so that they are
not pinched or interfering with other parts.
1. Place the side airbag on the seat-back frame (A).
Install new side airbag mounting screws (B).
2. Install the seat-back cover in the reverse order of
removal (see page 20-123).
3. Install the seat assembly (see page 20-118).
4. Move the front seat and the seat-back through their
full ranges of movement, making sure the harness
wires are not pinched or interfering with other parts.
5. Do the battery terminal reconnection procedure
(see page 22-68).
6. Clear any DTCs (see page 24-23).
7. After installing the side airbag, confirm proper
system operation: Turn the ignition switch to ON
(II); the SRS indicator should come on for about
6 seconds and then go off.
Replace.
08/08/21 14:01:56 61SNR030_240_0191
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст