Acura CSX. Manual — part 619
*90
−
+
+
−
+
−
−
+
−
−
−
+
+
−
−
+
+
+
−
+
+
−
+
+
23-189
AUDIO UNIT
LT BLU
R
RR
RR
R
L
RR
RR
L
R
FR
FR
R
L
FR
YEL
PNK
PNK
LT GRN
LT GRN
PNK
LT GRN
GRY
GRY
GRY
BRN
BRN
BRN
A8
A16
A11
A2
BRN
GRY
A7
A15
A12
A3
BLU
ORN
FR
L
DRIVER’S
DOOR SPEAKER
LEFT
TWEETER
FRONT
PASSENGER’S
DOOR SPEAKER
LEFT
REAR SPEAKER
RIGHT
TWEETER
RIGHT
REAR SPEAKER
1
2
2
1
1
2
2
1
1
2
2
1
B4
B3
B5
B15
B13
B14
3
2
1
4
5
AUXILIARY JACK ASSEMBLY
R
AUX
L
AUX
AUX
DET
SGND
AUX
AUX
GND
GRY
GND
AUX
AUX
SGND
BLU
BRN
DET
AUX
WHT
AUX
L
YEL
AUX
R
GRN
BUS
A13
R
R
E13
R
A5
E5
R
A14
L
L
E14
E4
GA-NET
A10
E10
BUS
GA-NET
E9
A9
A11
E11
E2
A2
A1
E1
E6
L
L
A6
PNK
BLU
BLK
LT BLU
BLU
RED
GRN
BLK
WHT
USB ADAPTER UNIT
A4
GA-NET
BUS
BUS
GA-NET
GRY
BUS SH
BUS SH
AUDIO
4
USB
GND
B4
3
B3
USB
DATA
2
USB
DATA
B2
B1
USB
VBUS
B5
1
5
USB
SH
USB ADAPTER
AUX
GND
SH
E3
BRN
A3
BRN
BUS SH
GA-NET
BUS SH
GA-NET
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
GRY
ACC
SYS
SYS
ACC
B
B
GND
GND
: GA-NET
: Shielding
*: The shielded wires have a heat-shrunk tube
insulating the outside of the wire. The color
of the insulating tube, typically black or dark gray,
may not match the color of the wire listed on the
schematic.
*
*
*
*
*
08/08/21 14:09:49 61SNR030_230_0192
*01
*02
SNR9ANKJ10300000000BBAT00
Without Navigation
Serial Number Display Mode
Eight digits of the serial number (example 12345678)
23-190
Audio System
Self-diagnostic Function
A
The audio system has a self-diagnostic function.
To obtain the audio unit serial number on a vehicle, do the following:
NOTE:
• This procedure can only be performed when the battery power is disconnected from the audio unit and the audio
unit displays CODE.
• To obtain the navigation unit serial number, refer to ECU Info. in the navigation system diagnostic mode (see page
23-305).
1. Turn the ignition switch to ON (II).
2. Make sure the audio system is turned off.
3. Push and hold the preset No. 1 and No. 6 buttons.
4. While holding the buttons, push the VOL PUSH PWR knob (A) to ON.
5. Release the buttons and the self-diagnostic begins.
6. The display shows a 8 digit serial number.
7. Use all 8 numbers as the serial number when using the Interactive Network (iN) to retrieve the 5 digit anti-theft
code.
8. To end the self-diagnostic function, turn the audio unit off, or turn the ignition switch to LOCK (0).
08/08/21 14:09:49 61SNR030_230_0193
*03
How to check for audio system condition
No. 3 button
No. 4 button
No. 5 button
FM button (Push and hold 5 sec.)
CD button (Push and hold 5 sec.)
23-191
A
NOTE:
• The audio unit must be in the code enter screen before performing the self-diagnostic function.
• The self diagnostic function does not find every problem with the audio system. Check any official Honda service
website for more information about the audio system.
1. Turn the ignition switch to ON (II).
2. Make sure the audio system is turned off.
3. Push and hold the preset No. 1 and No. 6 buttons.
4. While holding the buttons, push the VOL PUSH PWR knob (A) to ON.
5. Release the buttons and the self-diagnostic begins.
6. When you are in the self-diagnostic mode, pressing a preset button starts.
Entire LCD lighting/light-out mode: Turns on/off the entire LCD to show the presence or absence of an LCD failure.
The entire display must appear. If there are dead segments, replace the audio unit.
Duty indication mode (for the Illumination dim): Indicates the duty for the Illumination dim when the dash lights
are on.
Vehicle speed pulse indication mode: Indicates the vehicle speed pulse.
Reception level check mode: Indicates the reception level (dB). When entering the reception level check mode, the
AM/FM button is used to change the main/sub antenna. See Reception level indication for more information.
DRAM residual quantity indication mode: Indicates the DRAM residual quantity.
08/08/21 14:09:49 61SNR030_230_0194
*04
Display Specifications
Speaker check mode
23-192
Audio System
Entry LCD Lighting
No. 3 button
Entry LCD Lights-outs
No. 3 button
Duty (for the illumination) indication
No. 4 button
Vehicle speed pulse indication
No. 5 button
Reception level indication
FM button
DRAM residual quantity indication
CD button
7. The end the self-diagnostic function, turn the audio unit off, or turn the ignition switch to LOCK (0).
8. Turn off the audio unit.
9. Push and hold the No. 1 and No. 3 buttons. While holding the buttons, push the VOL push PWR knob to ON.
Release the buttons and the speaker check mode begins. A low-frequency hum should sound for about one
minute. Change the test speaker by pushing the SKIP button. If you find a speaker(s) with no sound, check the
speaker and harness connections. If the connections are good, replace the speaker, and retest.
10. To end the self-diagnostic function, turn the audio unit off, or turn the ignition switch to LOCK (0).
08/08/21 14:09:50 61SNR030_230_0195
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст