RAM 4500 Chassis Cab (2022 year). Manual in english — page 12

STARTING AND OPERATING

187

4. Shift the transfer case into N (Neutral):



With manual shift transfer case, shift the

transfer case lever into N (Neutral).



With electronically shifted transfer case,

push and hold the transfer case N (Neutral)

button. Some models have a small,

recessed "N" button (at the center of the

transfer case switches) that must be

pressed using a ballpoint pen or similar

object. Other models have a rectangular N

(Neutral) switch, below the rotary transfer

case control knob. The N (Neutral) indicator

light will blink while the shift is in progress.

The light will stop blinking (stay on solid)

when the shift to N (Neutral) is complete.

After the shift is completed and the N

(Neutral) light stays on, release the N

(Neutral) button.

5. Release the parking brake.
6. Shift the transmission into REVERSE.
7. Release the brake pedal for five seconds and

ensure that there is no vehicle movement.

8. Repeat steps 6 and 7 with automatic

transmission in DRIVE.

9. Shift the transmission to NEUTRAL. Firmly

apply the parking brake. Turn off the engine.

For vehicles with Keyless Enter ‘n Go™, push

and hold the ENGINE START/STOP button until

the engine shuts off.

10. Shift the transmission into PARK.
11. Place the ignition in the OFF mode, and

remove the key fob.

12. Attach the vehicle to the tow vehicle using a

suitable tow bar.

13. Release the parking brake.

NOTE:

With electronically shifted transfer case:



Steps 2 through 3 are requirements that must

be met before pushing the N (Neutral) button,

and must continue to be met until the shift has

been completed. If any of these requirements

are not met before pushing the N (Neutral)

button or are no longer met during the shift, the

N (Neutral) indicator light will flash continuously

until all requirements are met or until the

N (Neutral) button is released.



The ignition must be in the ON/RUN mode for a

shift to take place and for the position indicator

lights to be operable. If the ignition is not in the

ON/RUN mode, the shift will not take place and

no position indicator lights will be on or flashing.



A flashing N (Neutral) position indicator light

indicates that shift requirements have not been

met.

Shifting Out Of N (Neutral)

Use the following procedure to prepare your

vehicle for normal usage:
1. Bring the vehicle to a complete stop, leaving

it connected to the tow vehicle.

2. Firmly apply the parking brake.
3. Press and hold the brake pedal.
4. Start the engine, and shift the transmission

into NEUTRAL.



With manual shift transfer case, shift the

transfer case lever to the desired position.



With electronically shifted transfer case

with rotary selector switch, push and hold

the transfer case N (Neutral) button until

the N (Neutral) indicator light turns off. After

the N (Neutral) indicator light turns off,

release the N (Neutral) button. After the N

(Neutral) button has been released, the

transfer case will shift to the position indi

-

cated by the selector switch.



With electronically shifted transfer case

with push-button selector switch, push and

hold the switch for the desired transfer case

position, until the N (Neutral) indicator light

turns off and the desired position indicator

light turns on.

4

188

STARTING AND OPERATING

NOTE:

When shifting the transfer case out of N (Neutral),

turning the engine off is not required, but may be

helpful to avoid gear clash. With 8-speed auto

-

matic transmission, the engine must remain

running, since turning the engine off will shift the

transmission to PARK (and the transmission must

be in NEUTRAL for the transfer case to shift out of

NEUTRAL).
5. Turn the engine off. Shift automatic

transmission into PARK. On 8-speed

transmissions the shifter will automatically

select PARK when the engine is turned off.

6. Release the brake pedal.
7. Disconnect vehicle from the tow vehicle.
8. Start the engine.
9. Press and hold the brake pedal.
10. Release the parking brake.
11. Shift the transmission into gear, release the

brake pedal, and check that the vehicle

operates normally.

NOTE:

With electronically shifted transfer case:



Steps 3 and 4 are requirements that must be

met before pushing the button to shift out of N

(Neutral), and must continue to be met until the

shift has been completed. If any of these

requirements are not met before pushing the

button or are no longer met during the shift, the

N (Neutral) indicator light will flash continuously

until all requirements are met or until the button

is released.



The ignition must be in the ON/RUN mode for a

shift to take place and for the position indicator

lights to be operable. If the ignition is not in the

ON/RUN mode, the shift will not take place and

no position indicator lights will be on or flashing.



A flashing N (Neutral) position indicator light

indicates that shift requirements have not been

met.

DRIVING TIPS

D

RIVING

O

N

S

LIPPERY

S

URFACES

Acceleration

Rapid acceleration on snow covered, wet, or other

slippery surfaces may cause the driving wheels to

pull erratically to the right or left. This phenomenon

occurs when there is a difference in the surface

traction under the rear (driving) wheels.

WARNING!

Rapid acceleration on slippery surfaces is

dangerous. Unequal traction can cause sudden

pulling of the rear wheels. You could lose control

of the vehicle and possibly have a collision.

Accelerate slowly and carefully whenever there

is likely to be poor traction (ice, snow, wet, mud,

loose sand, etc.).

STARTING AND OPERATING

189

(Continued)

(Continued)

D

RIVING

T

HROUGH

W

ATER

Driving through water more than a few inches/

centimeters deep will require extra caution to

ensure safety and prevent damage to your vehicle.

Flowing/Rising Water

Shallow Standing Water

Although your vehicle is capable of driving through

shallow standing water, consider the following

Warnings and Cautions before doing so.

WARNING!

Do not drive on or across a road or path where

water is flowing and/or rising (as in storm

run-off). Flowing water can wear away the road

or path's surface and cause your vehicle to sink

into deeper water. Furthermore, flowing and/or

rising water can carry your vehicle away swiftly.

Failure to follow this warning may result in

injuries that are serious or fatal to you, your

passengers, and others around you.

WARNING!



Driving through standing water limits your

vehicle’s traction capabilities. Do not exceed

5 mph (8 km/h) when driving through

standing water.



Driving through standing water limits your

vehicle’s braking capabilities, which increases

stopping distances. Therefore, after driving

through standing water, drive slowly and

lightly press on the brake pedal several times

to dry the brakes.



Failure to follow these warnings may result in

injuries that are serious or fatal to you, your

passengers, and others around you.

CAUTION!



Always check the depth of the standing water

before driving through it. Never drive through

standing water that is deeper than the bottom

of the tire rims mounted on the vehicle.



Determine the condition of the road or the

path that is under water and if there are any

obstacles in the way before driving through

the standing water.



Do not exceed 5 mph (8 km/h) when driving

through standing water. This will minimize

wave effects.

WARNING!



Driving through standing water may cause

damage to your vehicle’s drivetrain compo

-

nents. Always inspect your vehicle’s fluids

(i.e., engine oil, transmission, axle, etc.) for

signs of contamination (i.e., fluid that is milky

or foamy in appearance) after driving through

standing water. Do not continue to operate

the vehicle if any fluid appears contaminated,

as this may result in further damage. Such

damage is not covered by the New Vehicle

Limited Warranty.



Getting water inside your vehicle’s engine can

cause it to lock up and stall out, and cause

serious internal damage to the engine. Such

damage is not covered by the New Vehicle

Limited Warranty.

CAUTION!

4

190

(Continued)

MULTIMEDIA

UCONNECT SYSTEMS

For detailed information about your Uconnect 3 With

5-inch Display

Ú

page 211.

For detailed information about your Uconnect

5/5 NAV With 8.4-inch Display system or your

Uconnect 5 NAV With 12-inch Display system, refer

to your Uconnect Owner’s Manual Supplement.

NOTE:

Uconnect screen images are for illustration

purposes only and may not reflect exact software

for your vehicle.

CYBERSECURITY

Your vehicle may be a connected vehicle and may

be equipped with both wired and wireless

networks. These networks allow your vehicle to

send and receive information. This information

allows systems and features in your vehicle to

function properly.
Your vehicle may be equipped with certain security

features to reduce the risk of unauthorized and

unlawful access to vehicle systems and wireless

communications. Vehicle software technology

continues to evolve over time and FCA US LLC,

working with its suppliers, evaluates and takes

appropriate steps as needed. Similar to a

computer or other devices, your vehicle may

require software updates to improve the usability

and performance of your systems or to reduce the

potential risk of unauthorized and unlawful access

to your vehicle systems.
The risk of unauthorized and unlawful access to

your vehicle systems may still exist, even if the

most recent version of vehicle software (such as

Uconnect software) is installed.

NOTE:



FCA US LLC or your dealer may contact you

directly regarding software updates.



To help further improve vehicle security and

minimize the potential risk of a security breach,

vehicle owners should:



Routinely check www.driveuconnect.com

(US Residents) or www.driveuconnect.ca

(Canadian Residents) to learn about avail

-

able Uconnect software updates.



Only connect and use trusted media

devices (e.g. personal mobile phones,

USBs, CDs).

Privacy of any wireless and wired communications

cannot be assured. Third parties may unlawfully

intercept information and private communications

without your consent

Ú

page 103.

WARNING!



It is not possible to know or to predict all of the

possible outcomes if your vehicle’s systems

are breached. It may be possible that vehicle

systems, including safety related systems,

could be impaired or a loss of vehicle control

could occur that may result in an accident

involving serious injury or death.



ONLY insert trusted devices/components into

your vehicle. Media of unknown origin could

possibly contain malicious software, and if

installed in your vehicle, it may increase the

possibility for vehicle systems to be breached.



As always, if you experience unusual vehicle

behavior, take your vehicle to your nearest

authorized dealer immediately.

WARNING!

MULTIMEDIA

191

UCONNECT SETTINGS

The Uconnect system uses a combination of

buttons on the touchscreen and buttons on the

faceplate located on the center of the instrument

panel. These buttons allow you to access and

change the Customer Programmable Features.

Many features can vary by vehicle.
Buttons on the faceplate are located below and/or

beside the Uconnect system in the center of the

instrument panel. In addition, there is a Scroll/

Enter control knob located on the right side. Turn

the control knob to scroll through menus and

change settings. Push the center of the control

knob one or more times to select or change a

setting.
Your Uconnect system may also have Screen Off

and Mute buttons on the faceplate.
Push the Screen Off button on the faceplate to turn

off the Uconnect screen. Push the button again or

tap the screen to turn the screen on.
Press the Back Arrow button to exit out of a Menu

or certain option on the Uconnect system.
For the Uconnect 5 systems, push and hold the

Power button on the radio’s faceplate for a

minimum of 15 seconds to reset the radio.

C

USTOMER

P

ROGRAMMABLE

F

EATURES

Uconnect 5 NAV With 12-inch Display Touchscreen And

Faceplate Buttons

For the Uconnect 3 With 5-inch Display, the

Uconnect 5/5 NAV With 8.4-inch Display, and

Uconnect 5 NAV With 12-inch Display
For Uconnect 3, push the SETTINGS button on the

top on faceplate. In this menu, the Uconnect

system allows you to access all of the available

programmable features.
For Uconnect 5, push the Vehicle button, then

press the Settings tab on the top of the

touchscreen. In this menu, the Uconnect system

allows you to access all of the available

programmable features.

NOTE:



Only one touchscreen area may be selected at a

time.



Depending on the vehicle’s options, feature

settings may vary.

When making a selection, press the button on the

touchscreen to enter the desired menu. Once in

the desired menu, press and release the preferred

setting option until a check mark appears next to

the setting, showing that setting has been

selected. Once the setting is complete, press the

Vehicle button to exit to the screen. Pressing the

Up or Down Arrow button on the right side of the

screen will allow you to toggle up or down through

the available settings.

1 — Uconnect Buttons On The Touchscreen
2 — Uconnect Buttons On The Faceplate

5

192

MULTIMEDIA

My Profile

When the My Profile button is pressed on the touchscreen, the system displays options related to the vehicle’s profiles.

NOTE:

Depending on the vehicle’s options, feature settings may vary.

Setting Name

Description

Language

This setting will change the language of the Uconnect system and Instrument

Cluster Display. The available languages are English, Français, and Español.

Display Mode

This setting will adjust the display for the radio to “Auto” or “Manual”.

“Manual” allows for more customization with the radio display.

Display Brightness Headlights On

This setting will allow you to set the brightness when the headlights are on. To

access this setting, Display Mode must be set to “Manual”. The “+” setting will

increase the brightness; the “-” will decrease the brightness.

Display Brightness Headlights Off

This setting will allow you to set the brightness when the headlights are off. To

access this setting, Display Mode must be set to “Manual”. The “+” setting will

increase the brightness; the “-” will decrease the brightness.

Set Theme

This setting will allow you to change the display theme.

Units

The available settings are “Speed” (MPH or km/h), “Distance” (mi or km),

“Fuel Consumption” (MPG [US], MPG [UK], L/100 km, or km/L), “Pressure”

(psi, kPa, or bar), “Temperature” (°C or °F), Power” (HP [US], Gal HP [UK], or

kW), and “Torque” (lb-ft or Nm) units of measurement independently.

Touchscreen Beep

This setting will allow you to turn the touchscreen beep on or off.

Show Main Category Bar Labels

This setting will allow the main category bar labels to be shown on or off.

Navigation Next Turn Pop-ups Displayed in Cluster

This setting will display navigation prompts in the Instrument Cluster Display.

Phone Pop-ups Displayed In Cluster

This setting will display smartphone notifications and messages in the

Instrument Cluster Display.

MULTIMEDIA

193

Time Format

This setting will allow you to set the time format (AM/PM). Sync Time With GPS

must be “Off” for this setting to be available. The “12 hrs” setting will set the

time to a 12-hour format. The “24 hrs” setting will set the time to a 24-hour

format.

Voice Options

This setting will allow you to change the voice options for the radio to “Male”

or “Female”.

Wake Up Word

This setting will allow you to set the system “Wake Up” word. The available

options are “Off”, “Hey, Uconnect”, and “Hey, Ram”.

Voice Barge-in

This setting will allow Voice Barge-in to be turned on or off.

Show Command List

This setting will allow the Command List to be shown. The options are “On”

and “Off”.

Navigation Settings

This setting will redirect to the list of Navigation settings. Refer to your

Uconnect Owner’s Manual Supplement for further information.

Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel

This setting will activate the vehicle’s comfort system and heated seats or

heated steering wheel when the vehicle is remote started or ignition is

started. The “Off” setting will not activate the comfort systems. The “Remote

Start” setting will only activate the comfort systems when using Remote Start.

The “All Start” setting will activate the comfort systems whenever the vehicle

is started.

Radio Power Off

This setting will keep certain electrical features running after the engine is

turned off. When any door is opened, the electronics will deactivate. The

available settings are “0 sec”, “45 sec”, “5 min”, and “10 min”.

Radio Off With Door

This setting will allow you to determine if the radio shuts off when any of the

doors are opened.

Audio Settings

This setting will open the submenu, containing the audio settings

Ú

page 207.

Setting Name

Description

5

194

MULTIMEDIA

App Drawer Favoriting Pop-ups

This setting will allow you to favorite app drawer pop-ups with “On” and “Off”

options.

App Drawer Unfavoritings Pop-ups

This setting will allow you to unfavorite app drawer pop-ups with “On” and

“Off” options.

New Text Message Pop-ups

This setting will allow you to have pop-up notifications for new text messages.

Setting options are “On” and “Off”.

Missed Calls Message

This setting will allow you to have pop-up notifications for missed calls. Setting

options are “On” and “Off”.

Navigation Pop-ups

This setting will allow you to have pop-up notifications for Navigation. Setting

options are “On” and “Off”.

Reset App Drawer to Default Order

This setting will reset the app drawer to its factory default layout.

Restore Settings to Default

This setting will return all the previously changed settings to their factory

default.

Trip B

This setting will turn the Trip B feature in the cluster on or off.

Audio Info On Cluster

This setting will turn the audio info on the cluster on or off.

Digital Speed On All Cluster Screens

This setting will show the digital speedometer on all cluster screens.

Consumption Bar On Cluster Screen

This setting will show the digital fuel consumption bar on all cluster screens.

Custom Areas On Cluster

This setting will allow you to customize the information displayed on the

cluster.

Audio Repetition

This setting will turn the system audio repetition on or off.

More Profile Options

This setting will give access to more profile options.

Setting Name

Description

MULTIMEDIA

195

Display

When the Display button is pressed on the touchscreen, the system will display the options related to the theme (if equipped), brightness, and color of the

touchscreen. The available settings are:

NOTE:

Depending on the vehicle’s options, feature settings may vary.

Setting Name

Description

Language

This setting will change the language of the Uconnect system and Instrument

Cluster Display. The available languages are English, Français, and Español.

Display Mode

This setting will allow you to set the brightness manually or have the system

set it automatically. The “Auto” setting has the system automatically adjust

the display brightness. The “Manual” setting will allow the user to adjust the

brightness of the display.

Display Brightness With Headlights ON/Brightness

This setting will allow you to set the brightness when the headlights are on. To

access this setting, Display Mode must be set to Manual. The “+” setting will

increase the brightness; the “-” will decrease the brightness.

Display Brightness With Headlights OFF/Brightness

This setting will allow you to set the brightness when the headlights are off. To

access this setting, Display Mode must be set to Manual. The “+” setting will

increase the brightness; the “-” will decrease the brightness.

Set Theme

This setting will allow you to change the display theme.

Units

The available settings are “Speed” (MPH or km/h), “Distance” (mi or km),

“Fuel Consumption” (MPG [US], MPG [UK], L/100 km, or km/L), “Pressure”

(psi, kPa, or bar), “Temperature” (°C or °F), Power” (HP [US], Gal HP [UK], or

kW), and “Torque” (lb-ft or Nm) units of measurement independently.

Keyboard

This setting will change the keyboard type on the display. The selectable

keyboards are “ABCDEF Keyboard”, “QWERTY Keyboard”, and “AZERTY

Keyboard”.

5

196

MULTIMEDIA

Safety/Driving Assistance

Touchscreen Beep

This setting will allow you to turn the touchscreen beep on or off.

Control Screen Timeout

This setting allows you to set the Control Screen to turn off automatically after

five seconds or stay open until manually closed.

Navigation Next Turn Pop-ups Displayed in Cluster

This setting will display navigation prompts in the Instrument Cluster Display.

Phone Pop-ups Displayed In Cluster

This setting will display smartphone notifications and messages in the

Instrument Cluster Display.

Fuel Saver Display

This setting will enable fuel saver mode in the Instrument Cluster Display.

Ready To Drive Pop-ups

This setting will enable the Ready To Drive Pop-ups in the Instrument Cluster

Display.

Setting Name

Description

When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle’s safety settings. These

options will differ depending on the features equipped on the vehicle. The settings may display in list form or within subfolders on the screen. To access a

subfolder, select the desired folder; the available options related to that feature will then display on the screen.

NOTE:

Depending on the vehicle’s options, feature settings may vary.

Setting Name

Description

Forward Collision Warning Sensitivity

This setting will change the distance at which the Forward Collision Warning

(FCW) alert sounds. The “Medium” setting will have the FCW system signal

when an object is in view, and the possibility of a collision is detected. The

“Near” setting will have the FCW system signal when the object is closer to the

vehicle. The “Far” setting will have the FCW system signal when an object is at

a far distance from the vehicle.

MULTIMEDIA

197

Forward Collision Warning

This setting will turn the Forward Collision Warning system on or off. The “Off”

setting will deactivate the FCW system. The “Warning Only” setting will provide

only an audible chime when a collision is detected. The “Warning + Active

Braking” setting will provide an audible chime and apply some brake pressure

when a collision is detected.

Pedestrian Emergency Braking

This setting will turn the Pedestrian Emergency Braking system on or off.

LaneSense Warning

This setting will change the distance at which the steering wheel will provide

lane departure feedback. The available settings are “Early”, “Medium”, and

“Late”.

LaneSense Strength

This setting will change the strength of the steering wheel feedback during a

lane departure. The available settings are “Low”, “Medium”, and “High”.

ParkSense

This setting will change the type of ParkSense alert when a close object is

detected and provide both an audible chime and a visual display.

Front ParkSense Volume

This setting adjusts the volume of the Front ParkSense system. The available

settings are “Low”, “Medium”, and “High”.

Rear ParkSense Volume

This setting adjusts the volume of the Rear ParkSense system. The available

settings are “Low”, “Medium”, and “High”.

Rear ParkSense Braking Assist

This setting will turn the Rear ParkSense Braking Assist on or off.

Blind Spot Alert

This setting will change the type of alert provided when an object is detected

in a vehicle’s blind spot. The “Off” setting will turn off Blind Spot Alert. The

“Lights” setting will activate the Blind Spot Alert lights on the outside mirrors.

The “Lights & Chime” setting will activate both the lights on the outside

mirrors and an audible chime.

Trailer Length For Blind Spot Alert

This setting will auto detect the length of an attached trailer. The “Auto”

setting will have the system automatically set the trailer length. The “Max”

setting will always set the length to the maximum 39.5 ft (12 m).

Setting Name

Description

5

198

MULTIMEDIA

Clock

Hill Start Assist

This setting will turn the Hill Start Assist system on or off.

ParkView Backup Camera Delay

This setting will add a timed delay to the ParkView Backup Camera when

shifting out of REVERSE.

ParkView Backup Camera Active Guidelines

This setting will turn the ParkView Backup Camera Active Guidelines on or off.

ParkView Backup Camera Fixed Guidelines

This setting will turn the ParkView Backup Camera Fixed Guidelines on or off.

Tire Fill Assist

This setting will turn Tire Fill Assist on or off.

Power Side Steps

This setting will raise and lower or stow the Power Side Steps. The available

options are “Automatic” to raise and lower the Power Side Steps and “Stow” to

deactivate the Power Side Steps.

Setting Name

Description

When the Clock button is pressed on the touchscreen, the system displays the different options related to the vehicle’s internal clock.

NOTE:

Depending on the vehicle’s options, feature settings may vary.

Setting Name

Description

Sync Time With GPS

This setting will sync the time to the GPS receiver in the system. The system

will control the time via the GPS location.

Set Time And Format/Time Format

This setting will allow you to set the time format (AM/PM). Sync Time With GPS

must be off for this setting to be available. The “12 hrs” setting will set the

time to a 12-hour format. The “24 hrs” setting will set the time to a 24-hour

format.

MULTIMEDIA

199

Phone/Bluetooth®

Set Time Hours

This setting will allow you to set the hours. Sync Time With GPS must be off for

this setting to be available. The “+” setting will increase the hours. The “-”

setting will decrease the hours.

Set Time Minutes

This setting will allow you to set the minutes. Sync Time With GPS must be off

for this setting to be available. The “+” setting will increase the minutes. The

“-” setting will decrease the minutes.

Show Time in Status Bar

This setting will place the time in the radio’s status bar.

Setting Name

Description

When the Phone/Bluetooth® button is pressed on the touchscreen, the system displays the options related to Bluetooth® connectivity from an external audio

device or smartphone. The list of paired audio devices or smartphones can be accessed from this menu.

NOTE:

Depending on the vehicle’s options, feature settings may vary.

Setting Name

Description

Device Manager

This setting will open the Device Manager main screen.

Do Not Disturb All

This setting will open the Do Not Disturb All settings menu. The available

options are “On” and “Off”.

Enable Two Active Phones

This setting will enable or disable two active phones within the vehicle. The

setting options are “On” and “Off”.

Phone Pop-Ups Displayed In Cluster

This setting will activate phone message pop-ups in the Instrument Cluster

Display.

5

200

MULTIMEDIA

Voice

Navigation — If Equipped

When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle’s Voice Recognition feature.

NOTE:

Depending on the vehicle’s options, feature settings may vary.

Setting Name

Description

Voice Options

This setting will allow you to change the system’s voice to either “Male” or

“Female”.

Wake Up Word

This setting will allow you to set the system’s “Wake Up” word. The available

options are “Off”, “Hey, Uconnect”, and “Hey, Ram”.

Voice Barge-In

This setting allows you to respond to a Voice Response before the statement

is completed by the system. The available options are “On” and “Off”.

Show Command List

This setting will allow you to turn the Command List on or off. The “Always”

setting will always show the Command List. The “With Help” setting will show

the Command List and provide a brief description of what the command does.

The “Never” setting will turn the Command List off.

When the Navigation button is pressed on the touchscreen, the system displays options related to the vehicle’s built-in Navigation system. These settings can

change which icons display on the map, how “time to arrival is calculated”, and route types.
For more information on Navigation and settings, refer to your Uconnect Owner’s Manual Supplement.

MULTIMEDIA

201

Trailer Brake/Trailer

Camera

When the Trailer Brake/Trailer button is pressed on the touchscreen, the system will display settings related to trailer towing.

NOTE:

Depending on the vehicle’s options, feature settings may vary.

Setting Name

Description

Trailer Select

Select from “Trailer 1”, “Trailer 2”, “Trailer 3”, or “Trailer 4”. These trailer

designations can be used to save different trailer settings.

Trailer Brake Type

This setting will set the system to a specific trailer type. The available options

are “Light Electric”, “Heavy Electric”, “Light Electric-Over-Hydraulic”, and

“Heavy Electric-Over-Hydraulic”.

Trailer Name

This setting will personalize the trailer name depending on the type of trailer

you are hauling. Select the trailer name from the following list: trailer, boat,

car, cargo, dump, equipment, flatbed, gooseneck, horse, livestock,

motorcycle, snowmobile, travel, utility, and 5th wheel.

When the Camera button is pressed on the touchscreen, the system displays the options related to the vehicle’s camera features.

NOTE:

Depending on the vehicle’s options, feature settings may vary.

Setting Name

Description

Surround View Camera Delay

This setting will add a timed delay to the Surround View Camera when shifting

out of REVERSE.

Surround View Camera Guidelines

This setting will turn the Surround View Camera Guidelines on or off.

5

202

MULTIMEDIA

Mirrors & Wipers

ParkView Backup Camera Delay

This setting will add a timed delay to the ParkView Backup Camera when

shifting out of REVERSE.

ParkView Backup Camera Active Guidelines

This setting will turn the ParkView Backup Camera Active Guidelines on or off.

ParkView Backup Camera Fixed Guidelines

This setting will turn the ParkView Backup Camera Fixed Guidelines on or off.

Setting Name

Description

When the Mirrors & Wipers button is pressed on the touchscreen, the system displays the options related to the vehicle’s mirrors and wipers.

NOTE:

Depending on the vehicle’s options, feature settings may vary.

Setting Name

Description

Tilt Side Mirrors In Reverse

This setting will tilt the outside side-view mirrors when the ignition is in the

ON/RUN position and the transmission gear selector is in the REVERSE

position. The mirrors will move back to their previous position when the

transmission is shifted out of REVERSE. The available settings are “On” and

“Off”.

Rain Sensing Auto Wipers

This setting will turn the Rain Sensing Auto Wipers on or off.

Headlights With Wipers

This setting will turn the headlights on when the wipers are activated.