Acura RSX Honda Integra. Manual — part 345
05
05
*03
05
−
−
−
−
−
−
18-13
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
B
E
D
B
C
A
10 x 1.25 mm
39 N·m
(4.0 kgf·m, 29 lbf·ft)
’02-04 models:
’05-06 models:
180 °
REAR
FRONT
OUTSIDE
90 °
A
B
12 x 1.25 mm
59
69 N·m
(6.0
7.0 kgf·m,
43
51 lbf·ft)
14 x 2.0 mm
88
98.1 N·m
(9.0
10.0 kgf·m,
65
72.3 lbf·ft)
OUTSIDE
REAR
FRONT
07MAC-SL0A202
12 x 1.25 mm:
07AAF-SDAA100
14 x 2.0 mm:
071AF-S3VA000
A
14 x 1.5 mm
137 N·m
(14.0 kgf·m,
101 lbf·ft)
16 x 1.5 mm
157 N·m
(16.0 kgf·m,
116 lbf·ft)
C
D
E
B
8. Remove the flange bolt (A) and wheel sensor (B)
from the knuckle. Do not disconnect the wheel
sensor connector.
9. Remove the flange nut (A) while holding the joint
pin (B) with a hex wrench (C), and disconnect the
stabilizer link (D) from the lower arm (E).
10. Remove the lock pin (A) from the lower arm ball
joint, and remove the castle nut (B).
NOTE: During installation, insert the new lock pin
as shown after tightening the nut.
11. Disconnect the lower arm from the knuckle using
the special tools (see page 18-10).
12. Loosen the damper pinch bolts (A) while holding
the nuts (B), and remove the bolts and the nuts.
13. Remove the driveshaft outboard joint (C) from the
knuckle (D) by tapping the driveshaft end (E) with a
plastic hammer while drawing the knuckle outward,
then remove the knuckle.
NOTE: Do not pull the driveshaft end outward. The
driveshaft joint may come apart.
(cont’d)
05/06/27 18:17:15 61S6M040_180_0013
07
08
08
09
18-14
Front Suspension
Knuckle/Hub/Wheel Bearing Replacement (cont’d)
07GAF-SD40100
Press
B
A
07GAF-SD40100
B
A
C
A
B
C
07749-0010000
B
A
07746-0010500
14. Separate the hub (A) from the knuckle (B) using the
special tool and a hydraulic press. Be careful not to
deform the splash guard. Hold onto the hub to keep
it from falling when pressed clear.
15. Press the wheel bearing inner race (A) off of the
hub (B) using the special tool, commercially
available bearing separator (C), and a press.
16. Remove the snap ring (A) and the splash guard (B)
from the knuckle (C).
17. Press the wheel bearing (A) out of the knuckle (B)
using the special tools and a press.
05/06/27 18:17:16 61S6M040_180_0014
09
10
06
18-15
C
A
B
D
BLACK
SEAL SIDE
METAL COLOR
SEAL SIDE
07965-SD90100
INSIDE
E
A
D
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
B
C
A
B
07965-SD90100
07746-0010500
07749-0010000
18. Wash the knuckle and hub thoroughly in high flash
point solvent before reassembly.
19. Press a new wheel bearing (A) into the knuckle (B)
using the old bearing (C), a steel plate (D), the
special tool, and a press. Place the wheel bearing
on the knuckle with the pack seal side facing (E)
(metal color) toward the inside. Be careful not to
damage the sleeve of the pack seal.
20. Install the snap ring (A) securely in the knuckle (B).
21. Install the splash guard (C), and tighten the screws
(D) to the specified torque value.
22. Press a new hub bearing unit (A) onto the hub (B)
using the special tools and a press.
23. Install the knuckle/hub/hub bearing unit in the
reverse order of removal, and note these items:
• Be careful not to damage the ball joint boot when
installing the knuckle.
• Before connecting the ball joint to the arm,
degrease the threaded section and tapered
portion of the ball joint pin, and the arm
connecting hole, and the threaded section and
mating surface of the castle nut.
• First install all the components and lightly tighten
the bolts and nuts, then raise the suspension to
load it with the vehicle’s weight before fully
tightening to the specified torque values.
• Tighten all mounting hardware to the specified
torque values.
• Torque the castle nut to the lower torque
specification, then tighten it only far enough to
align the slot with the ball joint pin hole. Do not
align the castle nut by loosening it.
• Reinstall the lock pin on the castle nut after
torquing.
• Use a new spindle nut on reassembly.
• Before installing the new spindle nut, apply a
small amount of engine oil to the seating surface
of the nut. After tightening, use a drift to stake the
spindle nut shoulder against the driveshaft.
• Before installing the brake disc, clean the mating
surface of the front hub and the inside of the
brake disc.
• Before installing the wheel, clean the mating
surface of the brake disc and the inside of the
wheel.
• Check the front wheel alignment, and adjust it if
necessary (see page 18-4).
05/06/27 18:17:16 61S6M040_180_0015
01
02
S6M6A00B20200014202KBAT00
Special Tools Required
18-16
Front Suspension
Ball Joint Boot Replacement
A
C
D
B
A
Press
07965-SA50500
Front hub dis/assembly tool, 36 mm 07965-SA50500
1. Remove the boot.
2. Pack the interior and lip (A) of a new boot with fresh
grease. Keep the grease off of the boot-to-knuckle
mating surfaces (B).
3. Wipe the grease off the tapered section of the pin
(C), and pack fresh grease onto the base (D).
4. Install the boot onto the ball joint pin, then squeeze
it gently to force out any air. Do not let dirt or other
foreign materials get into the boot.
5. Press the boot with the special tool until the bottom
seats on the knuckle (A) evenly around.
6. After installing a boot, wipe any grease off the
exposed portion of the ball joint pin.
05/06/27 18:17:17 61S6M040_180_0016
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст