Acura RSX Honda Integra. Manual — part 370
*01
S6M6A00J34300000000DAAT00
20-16
Mirrors
Component Location Index
MIRROR MOUNT COVER
LOCK BOLT
LOCK BOLT
LOCK WASHER
BRACKET BASE
HEADLINER CAP
POWER MIRROR
MIRROR HOLDER
REARVIEW MIRROR
POWER MIRROR ACTUATOR
Replacement, page 20-17
Replacement, page 20-18
Replacement, page 20-18
Replacement, page 22-139
05/06/27 18:21:57 61S6M040_200_0017
01
02
S6M6A00J34300044051KBAT00
20-17
Power Mirror Replacement
Fastener Location
: Clip, 1
A
Fastener Locations
: Nut, 3
A
B
5 x 0.8 mm
5 N·m
(0.5 kgf·m, 4 lbf·ft)
1. Lower the door glass fully.
2. Carefully pry out the mirror mount cover (A) by
hand in the sequence shown.
3. Remove the door panel (see page 20-5).
4. Disconnect the connector (A). While holding the
mirror (B), remove the nuts, then remove the
mirror. Take care not to scratch the door.
5. Install the mirror in the reverse order of removal,
and make sure the connector is plugged in properly.
05/06/27 18:21:57 61S6M040_200_0018
01
S6M6A00J34300044021KBAT00
01
02
S6M6A00J34300034651KBAT02
Special Tools Required
20-18
20-18
Mirrors
Mirror Holder Replacement
Rearview Mirror Replacement
A
D
F
G
I
C
H
E
B
G
A
H
C
D
C
B
A
B
Fastener Locations
: Screw, 3
A
5 x 0.8 mm
4 N·m
(0.4 kgf·m,
3 lbf·ft)
NOTE: Put on gloves to protect your hands.
1. Carefully push on the top edge of the mirror holder
(A) by hand.
2. Insert a flat-tip screwdriver (B) wrapped with
protective tape between the mirror holder and
mirror housing (C), and detach the bottom clips (D).
Put a shop towel (E) on the opening edge of the
mirror housing to prevent damage. Take care not to
scratch the mirror housing.
3. Carefully pull out the bottom edge of the mirror
holder, then separate the adhesive (F), and release
the side clips (G).
4. Separate the mirror holder from the actuator (H) by
releasing the hooks (I). If equipped, disconnect the
mirror defogger connectors from the heater pad
terminals.
5. If equipped, reconnect the mirror defogger
connectors.
6. Reattach the hooks of the mirror holder to the
actuator, then position the mirror holder on the
actuator. Carefully push on the clip portions of the
mirror holder until the mirror holder locks into
place.
7. Check the operation of the actuator.
KTC trim tool set SOJATP2014
NOTE: Use the appropriate tool from the KTC trim tool
set to avoid damage when prying components.
1. Using a trim tool, carefully remove the headliner
cap (A) by releasing the hooks (B). Take care not to
scratch the cap and headliner (C).
2. Remove the screws, then remove the rearview
mirror (A).
3. Install the mirror in the reverse order of removal.
05/06/27 18:21:58 61S6M040_200_0019
*01
S6M6A00J54400000000DAAT00
20-19
Glass
Component Location Index
WINDSHIELD
MOLDING
WINDSHIELD
FASTENER, 2
(Clip-type, body side)
(Required for replacement or reinstallation)
WINDSHIELD
SIDE TRIM
SIDE RUBBER DAM
(Required for
replacement or
reinstallation)
LOWER RUBBER DAM
REAR WINDOW
WINDOW ANTENNA
TERMINAL COVER
WINDOW ANTENNA
TERMINAL BASE
REAR WINDOW MOLDING
UPPER FASTENER, 2
(Self-adhesive-type, glass side)
(Required for replacement or reinstallation)
LOWER FASTENER, 2
(Self-adhesive-type, body side)
(Required for replacement
or reinstallation)
RETAINER, 8
SIDE RUBBER DAM
FASTENER, 2
(Self-adhesive-type, glass side)
(Required for replacement or reinstallation)
REAR WIPER SEAL
LOWER FASTENER, 2
(Self-adhesive-type, glass side)
(Required for replacement
or reinstallation)
UPPER FASTENER, 2
(Self-adhesive-type, body side)
(Required for replacement
or reinstallation)
REAR WINDOW
UPPER SEAL
SPACER, 1
(cont’d)
Replacement, page 20-21
Replacement, page 20-27
Replacement,
page 20-27
05/06/27 18:21:59 61S6M040_200_0020
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст