Acura RSX Honda Integra. Manual — part 357
01
02
03
04
S6M6A00D14300014751KBAT00
19-25
Brake Hose Replacement
B
C
A
B
A
C
B
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
C
34 N·m
(3.5 kgf·m,
25 lbf·ft)
A
D
10 x 1.0 mm
15 N·m
(1.5 kgf·m, 11 lbf·ft)
A
NOTE:
• Before reassembling, check that all parts are free of
dust and other foreign particles.
• Replace parts with new ones whenever specified to
do so.
• Do not spill brake fluid on the vehicle; it may damage
the paint; if brake fluid gets on the paint, wash it off
immediately with water.
• To prevent dripping, cover disconnected line joints
with rags or shop towels.
1. Replace the brake hose (A) if the hose is twisted,
cracked, or if it leaks.
2. Disconnect the brake hose from the brake line (B)
using a 10 mm flare nut wrench (C).
3. Remove the flange bolt (A), and remove the brake
hose brackets from the damper.
4. Remove and discard the hose clip (B).
5. Remove the banjo bolt (C), and remove the brake
hose from the caliper.
6. Install the brake hose bracket (A) on the damper
with the flange bolt (B) first, then connect the brake
hose to the caliper with the banjo bolt (C) and new
sealing washers (D).
7. Install the brake hose onto the hose bracket with a
new hose clip (A).
8. Connect the brake line to the brake hose.
9. After installing the brake hose, bleed the brake
system (see page 19-8).
10. Do the following checks:
• Check the brake hose and line joint for leaks, and
tighten if necessary.
• Check the brake hoses for interference and
twisting.
05/06/27 18:19:48 61S6M040_190_0025
*01
S6M6A00D00060845111KBAT00
Exploded View
19-26
Conventional Brake Components
Parking Brake Cable Replacement
PARKING BRAKE LEVER
BRACKET
ADJUSTING NUT
EQUALIZER
PARKING
BRAKE
SWITCH
(Sliding surface)
PARKING BRAKE LEVER
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
PARKING BRAKE CABLE
Check for smooth
operation.
Check for faulty movement.
05/06/27 18:19:48 61S6M040_190_0026
02
03
19-27
A
A
C
B
NOTE:
• The parking brake cables must not be bent or
distorted. This will lead to stiff operation and
premature failure.
• Refer to the Exploded View as needed during this
procedure.
1. Release the parking brake lever fully.
2. Remove the center console rear cover (see page
20-62).
3. Loosen the parking brake cable adjusting nut (A).
4. Remove the parking brake cable clip (A) from the
brake cable (B).
5. Disconnect the parking brake cable from the lever
(C).
6. Remove the parking brake cable mounting
hardware, then remove the cable.
7. Install the new cable in the reverse order of
removal, and note these items:
• Be careful not to bend or distort the cable.
• Make sure the parking brake cable clip is fully
seated on the cable housing.
• Do the parking brake adjustment (see page 19-7).
05/06/27 18:19:49 61S6M040_190_0027
S6M6A000000000J1901ZAAT00
05/06/27 18:19:49 61S6M040_190_0028
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст