Acura RSX Honda Integra. Manual — part 437
01
S6M6A04J32133122311FCAT00
Canada
22-86
Exterior Lights
Daytime Running Lights Control Unit Input Test
WHT/BLU
GRN/ORN
BLU/RED
RED/BLK
RED/BLU
BLK
GRN/RED
YEL/RED
RED
BLK
RED/YEL
RED/BLU
RED/GRN
B
A
1. Remove the driver’s dashboard lower cover (see page 20-63).
2. Disconnect the 14P connector (A) from the daytime running lights control unit (B).
3. Inspect the connector and socket terminals to be sure they are all making good contact.
• If the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
• If the terminals look OK, go to step 4.
Wire side of
female terminals
05/06/27 18:03:32 61S6M040_220_0087
Cavity
Wire
Test condition
Test: Desired result
Possible cause if result is not obtained
22-87
4. Make these input tests at the connector.
• If any test indicates a problem, find and correct the cause, then recheck the system.
• If all the input tests prove OK, the control unit must be faulty; replace it.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2
RED/BLU
Under all conditions
Check for voltage to ground:
There should be battery voltage.
Blown No. 14 (30 A) fuse in the under-hood
fuse/relay box
Blown No. 3 (10 A) fuse in the under-dash
fuse/relay box
An open in the wire
12
YEL/RED
Ignition switch ON (II)
Check for voltage to ground:
There should be battery voltage.
Blown No. 12 (7.5 A) fuse in the under-dash
fuse/relay box
An open in the wire
4
BLK
Under all conditions
Check for continuity to ground:
There should be continuity.
Poor ground (G401)
An open in the wire
7
BLK
Under all conditions
Check for continuity to ground:
There should be continuity.
Poor ground (G401)
An open in the wire
3
RED/YEL
Combination light
switch ON (
)
Check for voltage to ground:
There should be battery voltage.
Blown No. 15 (20 A) fuse in the under-hood
fuse/relay box
Faulty headlight relay 2
Faulty combination light switch
An open in the wire
5
RED
Combination light
switch ON (
)
Check for voltage to ground:
There should be battery voltage.
Blown No. 17 (20 A) fuse in the under-hood
fuse/relay box
Faulty headlight relay 1
Faulty combination light switch
An open in the wire
1
RED/GRN
Combination light
switch ON (
), and
dimmer switch in
HIGH
Connect a jumper wire between
No. 3 and No. 1, and No. 8 and No. 4
terminals.
Left headlight (HIGH) and high beam
indicator light should come on.
Blown bulb
Faulty daytime running lights relay
Faulty combination light switch
Poor ground (G401)
An open in the wire
11
RED/BLK
Combination light
switch ON (
), and
dimmer switch in
HIGH
Connect a jumper wire between
No. 5 and No. 11, and No. 8 and
No. 4 terminals.
Right headlight (HIGH) should come
on.
Blown bulb
Faulty daytime running lights relay
Faulty combination light switch
Poor ground (G401)
An open in the wire
10
RED/BLU
Combination light
switch ON (
), and
dimmer switch in
HIGH
Connect a jumper wire between
No. 8 and No. 4 terminals.
Check for continuity to ground:
There should be continuity.
Faulty daytime running lights relay
Faulty combination light switch
Poor ground (G401)
An open in the wire
6
GRN/ORN
Parking brake lever
pulled
Check for continuity to ground:
There should be continuity.
Faulty parking brake switch
An open in the wire
8
BLU/RED
Under all conditions
Attach to ground:
Headlights (LOW) should come on.
Faulty headlight relays
Blown bulb
An open in the wire
9
WHT/BLU
Ignition switch ON (II)
Attach to ground:
The DRL indicator light should come
on.
An open in the wire
13
GRN/RED
Ignition switch ON (II)
Attach to ground:
The brake system light should come
on.
An open in the wire
05/06/27 18:03:32 61S6M040_220_0088
03
03
01
S6M6A00J32133131131KBAT00
’02-04 models
’05-06 models
22-89
22-89
Headlight Replacement
Do not adjust.
A
B
C
5. If necessary, open the hood and adjust the
headlights to local requirements by turning the
vertical adjuster.
1. Remove the front bumper.
• ’02-04 models (see page 20-90)
• ’05-06 models (see page 20-91)
2. Disconnect the connectors (A) from the headlight
(B).
3. Remove the five mounting bolts, then remove the
corner upper beam (C) and headlight assembly.
4. Install in the reverse order of removal.
5. After replacement, adjust the headlights to local
requirements.
05/06/27 18:03:33 61S6M040_220_0090
01
02
S6M6A00J32100017101FHAT00
22-90
Exterior Lights
Combination Light Switch Test/Replacement
A
B
Terminal
Position
Headlight switch
OFF
LOW
HIGH
7
12
13
4
2
10
11
LEFT
NEUTRAL
RIGHT
Terminal
Position
Light switch:
Turn signal switch:
ON
OFF
Passing switch
1. Remove the dashboard lower cover (see page 20-63).
2. Remove the steering column covers (see page 17-25).
3. Disconnect the 16P connector (A) from the combination light switch (B).
4. Remove the two screws, then pull out the combination light switch.
5. Inspect the connector terminals to be sure they are all making good contact.
• If the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
• If the terminals look OK, check for continuity between the terminals in each switch position according to the
tables.
6. If the continuity is not as specified in the table, replace the switch.
05/06/27 18:03:57 61S6M040_220_0091
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст