Acura RSX Honda Integra. Manual — part 186
−
01
02
S6M6AALK72100090498FAAT00
−
−
−
−
−
−
−
−
DTC P0498:
YES
NO
YES
NO
YES
NO
YES
NO
11-450
EVAP System
DTC Troubleshooting (cont’d)
EVAP CANISTER VENT SHUT VALVE 2P CONNECTOR
ECM/PCM CONNECTOR E (31P)
VSV
(LT GRN/RED)
EVAP Canister Vent Shut Valve
Circuit Low Voltage
(2005-2006 models)
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS, then wait 5 seconds.
3. Check for Temporary DTCs or DTCs with the HDS.
Go to step 6.
Go to step 4.
4. Do the EVAP CVS ON in the INSPECTION MENU
with the HDS.
5. Check for Temporary DTCs or DTCs with the HDS.
Go to step 6.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the EVAP canister vent shut valve and the ECM/
PCM.
6. Turn the ignition switch OFF.
7. Disconnect the EVAP canister vent shut valve 2P
connector.
8. Measure resistance between EVAP canister vent
shut valve 2P connector terminals No. 1 and No. 2.
Go to step 9.
Go to step 12.
9. Jump the SCS line with the HDS.
10. Disconnect ECM/PCM connector E (31P).
11. Check for continuity between ECM/PCM connector
terminal E19 and body ground.
Repair short in the wire between the EVAP
canister vent shut valve and the ECM/PCM (E19),
then go to step 13.
Go to step 19.
Terminal side of male terminals
Wire side of female terminals
Is DT C P0498 indicated?
Is DT C P0498 indicated?
Is ther e about 25
30
at r oom temper atur e?
Is ther e continuity?
05/06/27 17:43:18 61S6M040_110_0450
−
−
−
−
YES
NO
YES
NO
11-451
12. Replace the EVAP canister vent shut valve
(see page 11-474).
13. Reconnect all connectors.
14. Turn the ignition switch ON (II).
15. Reset the ECM/PCM with the HDS.
16. Do the ECM/PCM idle learn procedure (see page
11-349).
17. Do the EVAP CVS ON in the INSPECTION MENU
with the HDS.
18. Check for Temporary DTCs or DTCs with the HDS.
If DTC P0498 is indicated, check for poor
connections or loose terminals at the EVAP canister
vent shut valve and the ECM/PCM, then go to step 1.
If any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.
Troubleshooting is complete.
19. Update the ECM/PCM if it does not have the latest
software, or substitute a known-good ECM/PCM
(see page 11-6).
20. Do the EVAP CVS ON in the INSPECTION MENU
with the HDS.
21. Check for Temporary DTCs or DTCs with the HDS.
If DTC P0498 is indicated, check for poor
connections or loose terminals at the EVAP canister
vent shut valve and the ECM/PCM, then go to step 1.
If any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-284).
Ar e any T empor ar y DT Cs or DT Cs indicated?
Ar e any T empor ar y DT Cs or DT Cs indicated?
05/06/27 17:44:48 61S6M040_110_0451
−
01
02
S6M6AALK72100090499FAAT00
−
−
−
−
−
−
DTC P0499:
YES
NO
YES
NO
YES
NO
11-452
EVAP System
DTC Troubleshooting (cont’d)
EVAP CANISTER VENT SHUT VALVE 2P CONNECTOR
IG1 (BLK/ORN)
EVAP CANISTER VENT SHUT VALVE 2P CONNECTOR
EVAP Canister Vent Shut Valve
Circuit High Voltage
(2005-2006 models)
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS, then wait 5 seconds.
3. Do the EVAP CVS ON in the INSPECTION MENU
with the HDS.
4. Check for Temporary DTCs or DTCs with the HDS.
Go to step 5.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the EVAP canister vent shut valve and the ECM/
PCM.
5. Turn the ignition switch OFF.
6. Disconnect the EVAP canister vent shut valve 2P
connector.
7. Turn the ignition switch ON (II).
8. Measure voltage between EVAP canister vent shut
valve 2P connector terminal No. 2 and body ground.
Go to step 9.
Repair open in the wire between the EVAP
canister vent shut valve and the No. 4 ACG (10 A)
fuse in the under-dash fuse/relay box, then go to
step 16.
9. Turn the ignition switch OFF.
10. Measure resistance between EVAP canister vent
shut valve 2P connector terminals No. 1 and No. 2.
Go to step 11.
Go to step 15.
Wire side of female terminals
Terminal side of male terminals
Is DT C P0499 indicated?
Is ther e batter y voltage?
Is ther e about 25
30
at r oom temper atur e?
05/06/27 17:44:48 61S6M040_110_0452
03
04
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
11-453
EVAP CANISTER VENT SHUT VALVE 2P CONNECTOR
VSV (LT GRN/RED)
JUMPER WIRE
ECM/PCM CONNECTOR E (31P)
VSV
(LT GRN/RED)
11. Jump the SCS line with the HDS.
12. Disconnect ECM/PCM connector E (31P).
13. Connect EVAP canister vent shut valve 2P
connector terminal No. 1 to body ground with a
jumper wire.
14. Check for continuity between ECM/PCM connector
terminal E19 and body ground.
Go to step 22.
Repair open in the wire between the EVAP
canister vent shut valve and the ECM/PCM (E19),
then go to step 16.
15. Replace the EVAP canister vent shut valve
(see page 11-474).
16. Reconnect all connectors.
17. Turn the ignition switch ON (II).
18. Reset the ECM/PCM with the HDS.
19. Do the ECM/PCM idle learn procedure (see page
11-349).
20. Do the EVAP CVS ON in the INSPECTION MENU
with the HDS.
21. Check for Temporary DTCs or DTCs with the HDS.
If DTC P0499 is indicated, check for poor
connections or loose terminals at the EVAP canister
vent shut valve and the ECM/PCM, then go to step 1.
If any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.
Troubleshooting is complete.
22. Update the ECM/PCM if it does not have the latest
software, or substitute a known-good ECM/PCM
(see page 11-6).
23. Do the EVAP CVS ON in the INSPECTION MENU
with the HDS.
24. Check for Temporary DTCs or DTCs with the HDS.
If DTC P0499 is indicated, check for poor
connections or loose terminals at the EVAP canister
vent shut valve and the ECM/PCM, then go to step 1.
If any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-284).
Wire side of female terminals
Wire side of female terminals
Is ther e continuity?
Ar e any T empor ar y DT Cs or DT Cs indicated?
Ar e any T empor ar y DT Cs or DT Cs indicated?
05/06/27 17:44:48 61S6M040_110_0453
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст