Acura RSX Honda Integra. Manual — part 488
−
−
02
03
04
−
−
−
−
YES
NO
YES
NO
23-84
SRS
DTC Troubleshooting (cont’d)
BLK
BLU/RED
BLK
RED/BLU
FRONT PASSENGER’S SEAT BELT
BUCKLE SWITCH 3P CONNECTOR
FLOOR WIRE HARNESS 3P CONNECTOR
BLK
C
7. Unbuckle the front passenger’s seat belt.
• Check resistance between the No. 1 and No. 2
terminals of the front passenger’s seat belt
buckle switch 3P connector. There should be
0
1
.
• Check resistance between the No. 1 and No. 3
terminals of the same connector. There should
be an open circuit or at least 1 M
.
Go to step 8.
Replace the front passenger’s seat belt buckle
assembly (see page 23-4), and clear the DTC.
8. Check resistance between the No. 1 terminal of the
floor wire harness 3P connector and body ground.
There should be 0
1
.
Go to step 9.
Open in floor wire harness or poor ground
connection at G501. If G501 is OK, replace the floor
wire harness.
9. Disconnect the negative cable from the battery.
10. Disconnect SRS unit connector C (8P) from the SRS
unit.
Terminal side of male terminals
Terminal side of male terminals
Wire side of female terminals
Ar e the r esistance as specif ied?
Is the r esistance as specif ied?
05/06/27 18:10:21 61S6M040_230_0084
−
−
05
06
07
08
−
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
YES
NO
23-85
FLOOR WIRE HARNESS 3P CONNECTOR
YEL
FLOOR WIRE HARNESS 3P CONNECTOR
ORN
FLOOR WIRE HARNESS
3P CONNECTOR
ORN
SRS UNIT CONNECTOR C (8P)
ORN
FLOOR WIRE HARNESS
3P CONNECTOR
SRS UNIT CONNECTOR C (8P)
YEL
YEL
11. Check resistance between the No. 2 terminal of the
floor wire harness 3P connector and body ground.
There should be an open circuit or at least 1 M
.
Go to step 12.
Short to ground in the floor wire harness;
replace the floor wire harness.
12. Check resistance between the No. 3 terminal of the
floor wire harness 3P connector and body ground.
There should be an open circuit or at least 1 M
.
Go to step 13.
Short to ground in the floor wire harness;
replace the floor wire harness.
13. Check resistance between the No. 7 terminal of
SRS unit connector C (8P) and the No. 3 terminal of
the floor wire harness 3P connector. There should
be 0
1
.
Go to step 14.
Open in floor wire harness or seat subharness
(with BOSE sound system); replace the faulty
harness.
14. Check resistance between the No. 3 terminal of
SRS unit connector C (8P) and the No. 2 terminal of
the floor wire harness 3P connector. There should
be 0
1
.
Replace the SRS unit (see page 23-141).
Open in floor wire harness or the seat
subharness (with BOSE sound system); replace the
faulty harness.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
Is the r esistance as specif ied?
Is the r esistance as specif ied?
05/06/27 18:10:22 61S6M040_230_0085
01
02
03
S6M6A00K79100081096FAAT00
−
−
−
−
DTC 9-6:
Special Tools Required
YES
NO
YES
NO
23-86
SRS
DTC Troubleshooting (cont’d)
A
A
A
Faulty Left Front Impact Sensor
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead H 07YAZ-S3AA100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Check the
connections between SRS unit connector A (18P)
and the SRS unit, between the engine
compartment wire harness 2P connector and the
left front impact sensor (see page 23-10) and at
connector C403.
Go to step 4.
Repair the poor connections and retest. If
DTC 9-6 is still present, go to step 4.
4. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
5. Disconnect the driver’s airbag 4P connector from
the cable reel (A).
6. Disconnect the front passenger’s airbag 4P
connector from the dashboard wire harness (A).
7. Disconnect both seat belt tensioner 2P connectors
from the floor wire harness (A).
Does the SRS indicator stay on?
Ar e the connections OK ?
05/06/27 18:10:22 61S6M040_230_0086
04
01
*01
*02
−
−
−
−
YES
NO
YES
NO
23-87
A
A
SRS UNIT CONNECTOR A (18P)
SRS UNIT CONNECTOR A (18P)
8. Disconnect the engine compartment wire harness
2P connector (A) from the left front impact sensor.
9. Disconnect SRS unit connector A (18P) from the
SRS unit.
10. Check resistance between the No. 10 and No. 11
terminals of SRS unit connector A (18P). There
should be an open circuit or at least 1 M
.
Go to step 11.
Short in the engine compartment wire
harness or dashboard wire harness; replace the
faulty harness.
11. Reconnect the battery negative cable.
12. Turn the ignition switch ON (II).
13. Check for voltage between the No. 10 terminal of
SRS unit connector A (18P) and body ground. There
should be 1 V or less.
Go to step 14.
Short to power in the engine compartment
wire harness or the dashboard wire harness;
replace the faulty harness.
(cont’d)
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the voltage as specif ied?
05/06/27 18:10:23 61S6M040_230_0087
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст