Acura RSX Honda Integra. Manual — part 159
01
02
06
03
S6M6AZFA20336147022FAAT00
−
−
−
−
−
−
2002-2004 models
YES
NO
YES
NO
YES
NO
11-342
Idle Control System
PSP Switch Signal Circuit Troubleshooting
ECM/PCM CONNECTORS
A (31P)
E (31P)
LG1 (BRN/YEL)
PSPSW
(LT GRN/BLK)
ECM/PCM CONNECTORS
A (31P)
E (31P)
LG1 (BRN/YEL)
PSPSW
(LT GRN/BLK)
PSP SWITCH 2P CONNECTOR
PSPSW
(LT GRN/BLK)
GND (BLK)
JUMPER
WIRE
ECM/PCM CONNECTORS
A (31P)
E (31P)
LG1 (BRN/YEL)
PSPSW
(LT GRN/BLK)
1. Turn the ignition switch ON (II).
2. Measure voltage between ECM/PCM connector
terminals A24 and E16.
Go to step 3.
Go to step 6.
3. Start the engine.
4. Turn the steering wheel to the full lock position.
5. Measure voltage between ECM/PCM connector
terminals A24 and E16.
The PSP switch signal is OK.
Go to step 11.
6. Turn the ignition switch OFF.
7. Disconnect the PSP switch 2P connector.
8. Turn the ignition switch ON (II).
9. At the harness side, connect PSP switch 2P
connector terminals No. 1 and No. 2 with a jumper
wire.
10. Measure voltage between ECM/PCM connector
terminals A24 and E16.
Replace the PSP switch.
Check for an open in the wire between the
ECM/PCM (E16) and the PSP switch, or an open in
wire between the PSP switch and G451.
11. Turn the ignition switch OFF.
12. Disconnect the PSP switch 2P connector.
13. Turn the ignition switch ON (II).
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is ther e less than 1.0 V ?
Is ther e batter y voltage?
Is ther e less than 1.0 V ?
05/06/27 17:40:57 61S6M040_110_0342
04
05
−
−
−
−
YES
NO
YES
NO
11-343
ECM/PCM CONNECTORS
A (31P)
E (31P)
LG1 (BRN/YEL)
PSPSW
(LT GRN/BLK)
ECM/PCM CONNECTOR E (31P)
PSPSW
(LT GRN/BLK)
14. Measure voltage between ECM/PCM connector
terminals A24 and E16.
Replace the PSP switch.
Go to step 15.
15. Turn the ignition switch OFF.
16. Disconnect ECM/PCM connector E (31P).
17. Check for continuity between body ground and
ECM/PCM connector terminal E16.
Repair short in the wire between ECM/PCM
(E16) and the PSP switch.
Update the ECM/PCM if it does not have the
latest software, or substitute a known-good ECM/
PCM (see page 11-6), then recheck. If the symptom/
indication goes away with a known-good ECM/PCM,
replace the original ECM/PCM (see page 11-284).
Wire side of female terminals
Wire side of female terminals
Is ther e batter y voltage?
Is ther e continuity?
05/06/27 17:40:57 61S6M040_110_0343
01
S6M6AZHA20336147022FAAT00
−
−
−
−
−
−
−
−
2005-2006 models
YES
NO
YES
NO
YES
NO
YES
NO
11-344
Idle Control System
PSP Switch Signal Circuit Troubleshooting (cont’d)
PSP SWITCH 2P CONNECTOR
PSPSW
(LT GRN/BLK)
1. Start the engine, and let it idle.
2. Align the steering wheel straight ahead.
3. Check the PSP SWITCH in the DATA LIST with the
HDS.
Go to step 4.
Go to step 12.
4. Turn the steering wheel to the full lock position.
5. Check the PSP SWITCH in the DATA LIST with the
HDS.
The PSP switch signal circuit is OK.
Go to step 6.
6. Disconnect the PSP switch 2P connector.
7. Check the PSP SWITCH in the DATA LIST with the
HDS.
Replace the PSP switch.
Go to step 8.
8. Turn the ignition switch OFF.
9. Jump the SCS line with the HDS.
10. Disconnect ECM/PCM connector E (31P).
11. Check for continuity between PSP switch 2P
connector terminal No. 1 and body ground.
Repair short in the wire between the ECM/
PCM (E16) and the PSP switch.
Update the ECM/PCM if it does not have the
latest software, or substitute a known-good ECM/
PCM (see page 11-6), then recheck. If the symptom/
indication goes away with a known-good ECM/PCM,
replace the original ECM/PCM (see page 11-284).
12. Turn the ignition switch OFF.
13. Disconnect the PSP switch 2P connector.
Wire side of female terminals
Does it indicate ON?
Does it change to OF F ?
Does it change to OF F ?
Is ther e continuity?
05/06/27 17:40:58 61S6M040_110_0344
02
03
04
05
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
11-345
PSPSW (LT GRN/BLK)
GND (BLK)
JUMPER WIRE
PSP SWITCH 2P CONNECTOR
PSPSW (LT GRN/BLK)
JUMPER WIRE
PSP SWITCH 2P CONNECTOR
ECM/PCM CONNECTOR E (31P)
PSPSW
(LT GRN/BLK)
PSP SWITCH 2P CONNECTOR
GND (BLK)
14. Connect PSP switch 2P connector terminals No. 1
and No. 2 with a jumper wire, then start the engine.
15. Check the PSPSW in the DATA LIST with the HDS.
Replace the PSP switch.
Go to step 16.
16. Turn the ignition switch OFF.
17. Remove the jumper wire from the PSP switch 2P
connector.
18. Jump the SCS line with the HDS.
19. Disconnect ECM/PCM connector E (31P).
20. Connect PSP switch 2P connector terminal No. 1 to
body ground with a jumper wire.
21. Check for continuity between body ground and
ECM/PCM connector terminal E16.
Go to step 22.
Repair open in the wire between the PSP
switch and the ECM/PCM (E16).
22. Check for continuity between PSP switch 2P
connector terminal No. 2 and body ground.
Update the ECM/PCM if it does not have the
latest software, or substitute a known-good ECM/
PCM (see page 11-6), then recheck. If the symptom/
indication goes away with a known-good ECM/PCM,
replace the original ECM/PCM (see page 11-284).
Repair open in the wire between the PSP
switch and G451.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Does it change to ON?
Is ther e continuity?
Is ther e continuity?
05/06/27 17:40:58 61S6M040_110_0345
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст