Acura RSX Honda Integra. Manual — part 27
01
02
01
S6M6A00A14100022205MAAT00
−
−
−
Special Tools Required
Auto-tensioner Spring Torque:
26.5
36.3 N·m (2.7
3.7 kg·m, 19.5
26.8 lbf·ft)
4-44
Charging System
Drive Belt Auto-tensioner Inspection
B
A
C
D
B
E
F
Belt tension release tool Snap-on YA9317 or equivalent,
commercially available
1. Check whether there is a change in the position of
the auto-tensioner indicator before starting the
engine and after starting the engine. If there is a
change in the position, replace the auto-tensioner.
2. Check for abnormal noise from the tensioner pulley.
If you hear abnormal noise, replace the tensioner
pulley.
3. Remove the drive belt (see page 4-43).
4. Move the auto-tensioner within its limit with the
belt tension release tool in the direction shown.
Check that the tensioner moves smoothly and
without any abnormal noise. If the tensioner does
not move smoothly or you hear abnormal noise,
replace the auto-tensioner.
5. Remove the auto-tensioner (see page 4-45).
6. Install the tensioner pulley.
7. Clamp the auto-tensioner (A) by using two 8 mm
bolts (B) and a vise (C) as shown. Do not clamp the
auto-tensioner itself.
8. Set the torque wrench (D) on the pulley bolt.
9. Align the indicator (E) on the tensioner arm with
center mark (F) on the tensioner base by using the
torque wrench, and measure the torque. If the
torque value is out of specification, replace the
auto-tensioner.
NOTE: If the indicator exceeds the center mark,
recheck the torque.
01
01
02
S6M6A00A14100022205KBAT00
4-45
Drive Belt Auto-tensioner Replacement
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
55 N·m (5.6 kgf·m, 41 lbf·ft)
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
1. Remove the drive belt (see page 4-43).
2. Remove the power steering (P/S) pump without
disconnecting the P/S hoses.
3. Remove the auto-tensioner pulley.
4. Remove the auto-tensioner.
5. Install in the reverse order of removal.
*02
*01
01
*03
S6M6A00A14100012901KDAT20
Removal
Installation
4-46
Charging System
Alternator Removal and Installation
A
B
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
A
B
8 N·m
(0.8 kgf·m, 6 lbf·ft)
1. Make sure you have the anti-theft codes for the
radio, then write down the customer’s radio station
presets.
2. Disconnect the negative cable from the battery first,
then disconnect the positive cable.
3. Remove the drive belt (see page 4-43).
4. Remove the auto-tensioner (see page 4-45).
5. Disconnect the alternator connector (A) and BLK
wire (B) from the alternator.
6. Remove the three bolts securing the alternator.
7. Remove the alternator.
1. Install the three bolts securing the alternator.
2. Connect the alternator connector (A) and BLK wire
(B) from the alternator.
3. Install the auto-tensioner (see page 4-45).
4. Install the drive belt (see page 4-43).
4-47
5. Connect the positive cable to the battery first, then
the connect negative cable.
6. Enter the anti-theft codes for the radio, then enter
the customer’s radio station presets.
7. Set the clock.
8. Do the engine control module (ECM)/powertrain
control module (PCM) idle learn procedure.
• 2002-2004 models (see page 11-349)
• 2005-2006 models (see page 11-349)
9. Do the power window control unit reset procedure
(see page 22-148).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст