Acura RSX Honda Integra. Manual — part 349
01
*01
03
S6M6A00B44100056861KDAT00
18-29
Stabilizer Link Removal/Installation
D
C
B
E
A
A
B
C
A
10 x 1.25 mm
38 N·m
(3.9 kgf·m, 28 lbf·ft)
B
10 x 1.25 mm
39 N·m
(4.0 kgf·m,
29 lbf·ft)
D
C
1. Raise the rear of the vehicle, and support it with
safety stands in the proper locations (see page
1-12).
2. Remove the rear wheel.
3. Remove the self-locking nut (A) and flange nut (B)
while holding the respective joint pin (C) with a hex
wrench (D), then remove the stabilizer link (E).
4. Install the stabilizer link (A) on the stabilizer bar (B)
and trailing arm with the joint pins set at the center
of their range of movement.
NOTE: The left stabilizer link has a yellow paint
mark (C), while the right stabilizer link has a white
paint mark.
5. Install the self-locking nut and flange nut, and
lightly tighten them.
NOTE: Use a new self-locking nut on reassembly.
6. Place a jack under the trailing arm at the knuckle
side end, and raise the suspension to load it with
the vehicle’s weight.
7. Tighten the new self-locking nut (A) and flange nut
(B) to the specified torque values while holding the
respective joint pins (C) with a hex wrench (D).
8. Reinstall all removed parts and test drive the
vehicle.
9. After 5 minutes of driving, tighten the self-locking
nut again to the specified torque values.
05/06/27 18:17:43 61S6M040_180_0029
01
02
S6M6A00B44100062201KDAT00
18-30
Rear Suspension
Upper Arm Removal/Installation
A
8 x 1.25 mm
22 N·m (2.2 kgf·m,
16 lbf·ft)
B
A
12 x 1.25 mm
59 N·m (6.0 kgf·m,
43 lbf·ft)
B
A
12 x 1.25 mm
59 N·m (6.0 kgf·m,
43 lbf·ft)
1. Raise the rear of the vehicle, and support it with
safety stands in the proper locations (see page
1-12).
2. Remove the rear wheel.
3. Place a floor jack under the trailing arm, and
support the suspension.
4. Remove the flange bolt (A) and wheel sensor
harness bracket (B).
5. Remove the flange bolts (A), and remove the upper
arm (B).
6. Install the upper arm in the reverse order of
removal, and note these items:
• First install all the suspension components and
lightly tighten the bolts and nuts, then place a
jack under the trailing arm, and raise the
suspension to load it with the vehicle’s weight
before fully tightening the bolts and nuts to the
specified torque values.
• Tighten all the mounting hardware to the
specified torque values.
• Before installing the wheel, clean the mating
surface of the brake disc and the inside of the
wheel.
• Check the wheel alignment, and adjust it if
necessary (see page 18-4).
05/06/27 18:17:44 61S6M040_180_0030
01
02
03
S6M6A00B44100059701KDAT00
18-31
Trailing Arm Removal/Installation
B
10 x 1.25 mm
39 N·m
(4.0 kgf·m,
29 lbf·ft)
D
12 x 1.25 mm
61 N·m
(6.2 kgf·m, 45 lbf·ft)
A
E
C
A
12 x 1.25 mm
112 N·m
(11.4 kgf·m, 82.5 lbf·ft)
A
12 x 1.25 mm
59 N·m
(6.0 kgf·m,
43 lbf·ft)
B
1. Raise the rear of the vehicle, and support it with
safety stands in the proper locations (see page
1-12).
2. Remove the rear wheel.
3. Remove the knuckle (see page 18-26).
4. Place the floor jack under the trailing arm (A) to
support it.
5. Remove the flange nut (B), and disconnect the
stabilizer link (C) from the trailing arm.
6. Remove the flange bolt (D), and disconnect the
damper (E) from the trailing arm.
7. Remove the trailing arm front mounting bolts (A).
8. Remove the trailing arm rear mounting bolt (A).
Do not loosen the special bolts (B) on the
trailing arm.
9. Lower the jack, and remove the trailing arm.
10. Install the trailing arm in the reverse order of
removal, and note these items:
• First install all the suspension components and
lightly tighten the bolts and nuts, then place a
jack under the trailing arm, and raise the
suspension to load it with the vehicle’s weight
before fully tightening the bolts and nuts to the
specified torque values.
• Tighten all the mounting hardware to the
specified torque values.
• Before installing the wheel, clean the mating
surface of the brake disc and the inside of the
wheel.
• Check the wheel alignment, and adjust it if
necessary (see page 18-4).
05/06/27 18:17:44 61S6M040_180_0031
*01
S6M6A00B44100019102KBAT00
Exploded View
18-32
Rear Suspension
Damper/Spring Replacement
SELF-LOCKING NUT
10 x 1.25 mm
29 N·m (3.0 kgf·m, 22 lbf·ft)
DAMPER MOUNTING
BASE
BUMP STOP
DAMPER SPRING
DAMPER UNIT
DAMPER MOUNTING
PLATE
DAMPER MOUNTING WASHER
DAMPER MOUNTING
COLLAR
RUBBER BUSHING
SPRING MOUNTING
CUSHION
BUMP STOP PLATE
BUMP STOP COVER
DUST COVER
RUBBER BUSHING
Replace.
Check for deformation.
Check for weakness
and damage.
Check for weakened
compression and damage.
Check for oil leaks,
gas leaks, and smooth
operation.
Check for bending or damage.
Check for weakness
and damage.
Check for deterioration
and damage.
Check for bending
and damage.
Check for bending and damage.
Check for weakness
and damage.
05/06/27 18:17:44 61S6M040_180_0032
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст