Acura RSX Honda Integra. Manual — part 326
01
S6M6A00E16236500000LDAT00
Exploded View
16-22
Driveline/Axle
Intermediate Shaft Reassembly
INTERMEDIATE SHAFT RING
FLANGE BOLT
10 x 1.25 mm
39 N·m
(4.0 kgf·m, 29 lbf·ft)
INTERMEDIATE
SHAFT BEARING
EXTERNAL SNAP RING
INTERMEDIATE SHAFT
BEARING SUPPORT RING
INTERNAL SNAP RING
BEARING SUPPORT
DOWEL BOLTS
10 x 1.25 mm
39 N·m
(4.0 kgf·m, 29 lbf·ft)
OUTER SEAL
SET RING
Replace.
Pack the interior of the outer seal.
Replace.
Replace.
05/06/27 18:13:00 61S6M040_160_0022
02
03
04
05
Special Tools Required
16-23
PRESS
B
A
07749-0010000
07746-0010400
A
B
PRESS
A
07746-0030400
• Driver 07749-0010000
• Attachment, 52 x 55 mm 07746-0010400
• Attachment, 35 mm I.D. 07746-0030400
• Oil seal driver 07GAD-PH70201
NOTE: Refer to the Exploded View as needed during
this procedure.
1. Clean the disassembled parts with solvent, and dry
them with compressed air. Do not wash the rubber
parts with solvent.
2. Press the intermediate shaft bearing (A) into the
bearing support (B) using the special tools and a
press.
3. Install, then seat the internal snap ring into the
groove of the bearing support.
4. Press the intermediate shaft (A) into the shaft
bearing using the special tool and a press.
5. Install, then seat the external snap ring (A) into the
groove of the intermediate shaft (B).
(cont’d)
05/06/27 18:13:00 61S6M040_160_0023
02
07
01
02
S6M6A00E16236500000KCAT00
16-24
16-24
Driveline/Axle
Intermediate Shaft Reassembly
(cont’d)
Intermediate Shaft Installation
PRESS
B
A
07GAD-PH70201
B
A
B
10 x 1.25 mm
39 N·m
(4.0 kgf·m,
29 lbf·ft)
A
10 x 1.25 mm
39 N·m
(4.0 kgf·m, 29 lbf·ft)
6. Install the outer seal (A) into the bearing support (B)
using the special tool and a press.
7. Install the set ring.
1. Use solvent or brake cleaner to thoroughly clean
the areas where the intermediate shaft (A) contacts
the transmission (differential), and dry with
compressed air. Do not wash the rubber parts with
solvent. Insert the intermediate shaft assembly into
the differential. Hold the intermediate shaft
horizontally to prevent damage to the differential
oil seal (B).
2. Install the flange bolt (A) and two dowel bolts (B).
Pack the interior
of the outer seal.
05/06/27 18:13:01 61S6M040_160_0024
03
16-25
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
3. Install the heat cover, and tighten the three bolts.
4. Install the right driveshaft (see page 16-17).
5. Refill the transmission with the recommended
transmission fluid:
• Manual transmission (see page 13-4)
• Automatic transmission (see page 14-272)
05/06/27 18:13:01 61S6M040_160_0025
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст