Acura RSX Honda Integra. Manual — part 66
01
24
01
26
9-6
Intake Manifold and Exhaust System
Intake Manifold Removal and Installation (cont’d)
D
A
D
B
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
C
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
A
B
C
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
B
A
3. Connect the hood switch connector (A), then install
the A/C line bracket mounting bolt (B), intake air
duct mounting bolt (C) and harness clamps (D).
4. Install the front bumper (see page 20-90).
5. Connect the IMT (IMRC) valve actuator control
solenoid valve connector (A), then install the PCV
hose (B) and IMT (IMRC) valve actuator control
solenoid valve mounting bolt (C).
6. Install the water bypass hoses.
7. Install the EVAP canister hose (A) and brake
booster vacuum hose (B).
28
29
9-7
B
C
A
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
8. Install the throttle cable (see page 11-409), then
adjust it (see page 11-408).
9. Install the cruise control actuator cable, then adjust
it (see page 4-71).
10. Install the air cleaner housing (A) and connect the
IAT sensor connector (B).
11. Install the breather hose (C).
12. Install the intake manifold cover.
13. After installation, check that all tubes, hoses, and
connectors are installed correctly.
14. Refill the radiator with engine coolant, and bleed
air from the cooling system with the heater valve
open (see step 7 on page 10-7).
15. Clean up any spilled engine coolant.
02
S6M6A10A20336335001KDAT00
Exploded View - K20A2, K20Z1 Engines
9-8
Intake Manifold and Exhaust System
Intake Manifold Removal and Installation (cont’d)
THROTTLE BODY
INTAKE MANIFOLD
BRACKET
INTAKE MANIFOLD
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
GASKET
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
INTAKE MANIFOLD
PLATE
GASKET
GASKET
Replace if cracked or
if mating surface is
damaged.
Replace.
Replace if cracked or
if mating surface is
damaged.
Replace.
Replace.
13
14
15
Removal - K20A2, K20Z1 Engines
9-9
C
B
A
C
B
A
1. Relieve fuel pressure (see page 11-360).
2. Remove the intake manifold cover.
3. Remove the EVAP canister hose (A), brake booster
vacuum hose (B), and vacuum hoses (C).
4. Disconnect the IAT sensor connector (A), and
remove the breather hose (B), then remove the air
cleaner housing (C).
(cont’d)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст