Acura RSX Honda Integra. Manual — part 19
*01
*02
04
01
K20A3 engine
K20A2, K20Z1 engines
K20A3 engine
K20A2, K20Z1 engines
Installation
4-12
Starting System
Starter Removal and Installation (cont’d)
A
B
A
B
8 x 1.25 mm
9 N·m (0.9 kgf·m, 7 lbf·ft)
10 x 1.25 mm
44 N·m
(4.5 kgf·m,
33 lbf·ft)
12 x 1.25 mm
64 N·m (6.5 kgf·m, 47 lbf·ft)
A
B
A
10 x 1.25 mm
44 N·m (4.5 kgf·m, 33 lbf·ft)
B
8 x 1.25 mm
9 N·m
(0.9 kgf·m, 7 lbf·ft)
12 x 1.25 mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
Disconnect the starter cable (A) from the B terminal
on the solenoid, then disconnect the BLK/WHT wire
(B) from the S terminal.
Remove the two bolts holding the starter, then
remove the starter.
1. Install the two bolts holding the starter.
2. Connect the starter cable (A) from the B terminal on
the solenoid, then connect the BLK/WHT wire (B)
from the S terminal. Make sure the crimped side of
the ring terminal is facing out.
8.
9.
03
02
01
4-13
A
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
B
8 x 1.25 mm
24 N·m
(2.4 kgf·m, 17 lbf·ft)
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
3. K20A2, K20Z1 engines: Install the bolt (A) securing
the harness bracket, then Install the intake manifold
brackets (B).
4. K20A2, K20Z1 engines: Install the front subframe
damper.
5. K20A3 engine: Connect the bolt securing the
harness bracket.
6. Connect the knock sensor connector.
7.
Enter the anti-theft codes for the radio, then enter
the customer’s radio station presets.
Set the clock.
2002-2004 models: Do the engine control module
(ECM) /powertrain control module (PCM) idle learn
procedure (see page 11-349).
Do the power window control unit reset procedure
(see page 22-148).
connect the negative cable.
Connect the positive cable to the battery first, then
Install the intake manifold.
8.
properly.
Start the engine to make sure the starter operates
9.
10.
11.
12.
13.
20
S6M6A11A46500056901LAAT00
Disassembly/Reassembly - K20A3 Engine
4-14
Starting System
Starter Overhaul
RING GEAR HOLDER
SWITCH PLUNGER
GEAR PLUNGER
BRUSH
HOLDER
PUSH NUT
GEAR COVER ASSEMBLY
SWITCH SHAFT
BRUSH
SPRING
END COVER
ARMATURE HOUSING
ARMATURE
DRIVE PLATE
PLANETARY GEAR
(Apply molybdenum
disulfide.)
(Apply molybdenum
disulfide.)
21
S6M6A10A46500056901LAAT00
Disassembly/Reassembly - K20A2, K20Z1 Engines
4-15
SOLENOID LEVER
GEAR HOUSING
OVERRUNNING
CLUTCH ASSEMBLY
BRUSH
ARMATURE
HOUSING
ARMATURE
END COVER
BRUSH HOLDER
STARTER SOLENOID
(cont’d)
(Apply molybdenum
disulfide.)
(Apply molybdenum
disulfide.)
(Apply molybdenum
disulfide.)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст