Acura RSX Honda Integra. Manual — part 491
01
*01
01
S6M6A00K79100081115FAAT00
−
−
−
−
YES
NO
Special Tools Required
YES
NO
DTC 11-5:
23-96
23-96
SRS
DTC Troubleshooting (cont’d)
B
SRS UNIT CONNECTOR B (18P)
B
A
07XAZ-S1A0200
07SAZ-TB4011A
11. Disconnect SRS unit connector B (18P) from the
SRS unit.
12. Turn the ignition switch ON (II).
13. Check for voltage between the No. 6 terminal of
SRS unit connector B (18P) and body ground, and
between the No. 17 terminal and body ground.
There should be 0.5 V or less.
Faulty SRS unit; replace the SRS unit
(see page 23-141).
Short to power in the floor wire harness;
replace the floor wire harness.
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead E 07XAZ-S1A0200
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the floor wire harness 2P connector (A)
from the driver’s side airbag (B).
5. Connect the SRS inflator simulator (2
connector) and the simulator lead E to the floor
wire harness 2P connector.
Short to Ground in Driver’s Side
Airbag Inflator
Wire side of female terminals
Is the voltage as specif ied?
Does the SRS indicator stay on?
05/06/27 18:10:26 61S6M040_230_0096
02
01
*01
−
−
−
−
YES
NO
YES
NO
23-97
B
A
B
SRS UNIT CONNECTOR B (18P)
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Short to ground in the driver’s side airbag
inflator; replace the driver’s side airbag (see page
23-134).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the front passenger’s side airbag 2P
connector (A) and both seat belt buckle tensioner
4P connectors (B).
11. Disconnect SRS unit connector B (18P) from the
SRS unit.
12. Check resistance between the No. 17 terminal of
the SRS unit connector B (18P) and body ground,
and between the No. 6 terminal and body ground.
There should be an open circuit or at least 1 M
.
Faulty SRS unit; replace the SRS unit
(see page 23-141).
Short to ground in the floor wire harness;
replace the floor wire harness.
Wire side of female terminals
Is DT C 11-5 indicated?
Is the r esistance as specif ied?
05/06/27 18:10:26 61S6M040_230_0097
01
02
S6M6A00K79100081121FAAT20
−
−
−
−
DTC 12-1:
Special Tools Required
YES
NO
YES
NO
23-98
SRS
DTC Troubleshooting (cont’d)
B
A
07XAZ-S1A0200
07SAZ-TB4011A
B
A
Open or Increased Resistance in
Front Passenger’s Side Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead E 07XAZ-S1A0200
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the floor wire harness 2P connector (A)
from the front passenger’s side airbag (B).
5. Connect the SRS inflator simulator (2
connector) and the simulator lead E to the floor
wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Open or increased resistance in the front
passenger’s side airbag inflator; replace the front
passenger’s side airbag (see page 23-134).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver’s side airbag 2P connector (A)
and both seat belt buckle tensioner 4P connectors
(B).
Does the SRS indicator stay on?
Is DT C 12-1 indicated?
05/06/27 18:10:27 61S6M040_230_0098
−
01
*01
01
S6M6A00K79100081123FAAT00
−
−
−
−
YES
NO
Special Tools Required
YES
NO
DTC 12-3:
23-99
23-99
B
SRS UNIT CONNECTOR B (18P)
B
A
07XAZ-S1A0200
07SAZ-TB4011A
11. Disconnect SRS unit connector B (18P) from the
SRS unit. Do not disconnect the simulator lead
from the floor wire harness 2P connector.
12. Check resistance between the No. 7 and No. 18
terminals of SRS unit connector B (18P). There
should be 2.0
3.0
.
Faulty SRS unit or poor connection at SRS
unit connector B (18P) and the SRS unit. Check the
connection; if the connection is OK, replace the
SRS unit (see page 23-141).
Open or increased resistance in the floor wire
harness; replace the floor wire harness.
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead E 07XAZ-S1A0200
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the floor wire harness 2P connector (A)
from the front passenger’s side airbag (B).
5. Connect the SRS inflator simulator (2
connector) and the simulator lead E to the floor
wire harness 2P connector.
(cont’d)
Short to Another Wire or
Decreased Resistance in Front Passenger’s
Side Airbag Inflator
Wire side of female terminals
Is the r esistance as specif ied?
Does the SRS indicator stay on?
05/06/27 18:10:27 61S6M040_230_0099
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст