Acura RSX Honda Integra. Manual — part 60
01
01
S6M6A10A32200043401KCAT00
K20A2, K20Z1 Engines
7-30
7-30
Engine Block
Oil Pan Installation (cont’d)
5. Tighten the bolts in two or three steps. In the final
step, tighten all bolts in sequence to 12 N·m
(1.2 kgf·m, 8.7 lbf·ft). Wipe off the excess liquid
gasket on the each side of crankshaft pulley and
flywheel/drive plate.
NOTE:
• Wait at least 30 minutes before filling the engine
with oil.
• Do not run the engine for at least 3 hours after
installing the oil pan.
6. If the engine is still in the vehicle, install the
subframe.
–1 Install the subframe. Align the reference lines
on the subframe with the bolt head center, then
tighten the bolts (see step 4 on page 5-12).
–2 Install the automatic transmission (ATF) filter
mounting bolt (see step 24 on page 5-16).
–3 Tighten the rear mount mounting bolts (see
step 5 on page 5-13).
–4 Tighten the new front mount mounting bolt
(see step 11 on page 5-15).
–5 Connect the suspension lower arm ball joints
(see step 10 on page 18-13).
1. Remove all of the old liquid gasket from the oil pan
mating surfaces, bolts, and bolt holes.
2. Clean and dry the oil pan mating surfaces.
3. Apply liquid gasket, P/N 08717-0004, 08718-0001,
08718-0002, 08718-0003 or 08718-0009, evenly to
the engine block mating surface of the oil pan.
NOTE: Do not install components if too much time
has passed after applying the liquid gasket (for P/N
08718-0002, no more than 4 minutes, for all others,
no more than 5 minutes). Instead, remove the old
residue and reapply the liquid gasket.
4. Install the oil pan.
Apply liquid gasket
along the broken line.
02
03
7-31
A
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
B
12 x 1.25 mm
64 N·m (6.5 kgf·m, 47 lbf·ft)
5. Tighten the bolts in two or three steps. In the final
step, tighten all bolts in sequence to 12 N·m
(1.2 kgf·m, 8.7 lbf·ft). Wipe off the excess liquid
gasket on the each side of crankshaft pulley and
flywheel/drive plate.
NOTE:
• Wait at least 30 minutes before filling the engine
with oil.
• Do not run the engine for at least 3 hours after
installing the oil pan.
6. Install the clutch cover (A), and tighten the two
bolts (B) securing the transmission.
7. If the engine is still in the vehicle, install the
subframe.
–1 Install the subframe. Align the reference lines
on the subframe with the bolt head center, then
tighten the bolts (see step 4 on page 5-12).
–2 Tighten the rear mount mounting bolts (see
step 5 on page 5-13).
–3 Tighten the new front mount mounting bolt
(see step 11 on page 5-15).
–4 Connect the suspension lower arm ball joints
(see step 10 on page 18-13).
01
01
S6M6A00A18316617513KCAT00
−
−
−
−
Special Tools Required
Oil Seal Installed Height:
5.5
6.5 mm (0.22
0.26 in.)
7-32
Engine Block
Transmission End Crankshaft Oil Seal Installation - In Car
07749-0010000
07ZAD-PNAA100
5.5
6.5 mm
(0.22
0.26 in.)
A
B
• Driver 07749-0010000
• Oil seal driver attachment 96 07ZAD-PNAA100
1. A/T model: Remove the transmission (see page
14-273), then remove the drive plate (see page
14-281).
2. M/T model: Remove the transmission (see page
13-5). Remove the pressure plate and clutch disc
(see page 12-12), then remove the flywheel
(see page 12-14).
3. Dry the crankshaft oil seal housing.
4. Use the special tools to drive a new oil seal
squarely into the block to the specified installed
height.
5. Measure the distance between the crankshaft (A)
and oil seal (B).
6. A/T model: Install the drive plate (see page 14-281),
then install the transmission (see page 14-282).
7. M/T model: Install the flywheel (see page 12-14),
then install the clutch disc and pressure plate
(see page 12-15). Install the transmission (see page
13-12).
S6M6A000000000J0801ZCAT00
Engine Mechanical
Engine Lubrication
. . . . . . . . . . . . . . . .
. . . . . . . . . .
. . . . . . . ..
. . . . . . . . . . . .
. . . . . . . ..
. . . . . . . . . . . . . . ..
. . . . . . . . . . . .
. . . . . . . . .
. . . . . . . ...
. . . . . . . . . . . ..
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . ..
. . . . . . . . . . . . . . . .
. . . . . . . . . .
. . . . . . . ..
. . . . . . . . . . . .
. . . . . . . ..
. . . . . . . . . . . . . . ..
. . . . . . . . . . . .
. . . . . . . . .
. . . . . . . ...
. . . . . . . . . . . ..
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . ..
Special Tools
. 8-2
Component Location Index
. 8-3
Symptom Troubleshooting Index
. 8-5
Oil Pressure Switch Test
. 8-6
Oil Pressure Switch Replacement
. 8-6
Oil Pressure Test
. 8-7
Engine Oil Replacement
. 8-8
Engine Oil Filter Replacement
. 8-9
Oil Filter Feed Pipe Replacement
. 8-10
Oil Cooler Replacement
. 8-10
Oil Jet Inspection
. 8-11
Oil Pump Overhaul
. 8-12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст