Acura RSX Honda Integra. Manual — part 480
01
01
S6M6A00K79100081035FAAT00
−
−
−
−
−
−
DTC 3-5:
Special Tools Required
YES
NO
YES
NO
YES
NO
23-52
SRS
DTC Troubleshooting (cont’d)
A
07TAZ-SZ5011A
07SAZ-TB4011A
A
07SAZ-TB4011A
07XAZ-SZ30100
C504
Short to Ground in Driver’s Seat Belt
Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead C 07TAZ-SZ5011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s seat belt tensioner 2P
connector from the floor wire harness (A).
5. Connect the SRS inflator simulator (2
connector) and the simulator lead C to the floor
wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Short to ground in the driver’s seat belt
tensioner; replace the driver’s seat belt (see page
23-4).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the floor wire harness 4P connector (A)
from the dashboard wire harness C504.
11. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the
dashboard wire harness 4P connector C504.
12. Reconnect the battery negative cable.
13. Erase the DTC memory.
14. Read the DTC.
Go to step 15.
Short to ground in the floor wire harness;
replace the floor wire harness.
15. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Does the SRS indicator stay on?
Is DT C 3-5 indicated?
Is DT C 3-5 indicated?
05/06/27 18:09:19 61S6M040_230_0052
03
02
*01
−
−
YES
NO
23-53
A
B
C
A
SRS UNIT CONNECTOR A (18P)
16. Disconnect the driver’s airbag connector (A), front
passenger’s airbag connector (B), and front
passenger’s seat belt tensioner connector (C).
17. Disconnect SRS unit connector A (18P) from the
SRS unit.
18. Disconnect the simulator lead from the dashboard
wire harness 4P connector.
19. Check resistance between the No. 8 terminal of
SRS unit connector A (18P) and body ground, and
between the No. 17 terminal and body ground.
There should be an open circuit or at least 1 M
.
Faulty SRS unit; replace the SRS unit
(see page 23-141).
Short to ground in the dashboard wire
harness; replace the dashboard wire harness.
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
05/06/27 18:09:19 61S6M040_230_0053
01
02
S6M6A00K79100081211FAAT00
−
−
−
−
DTC 21-1:
Special Tools Required
YES
NO
YES
NO
23-54
SRS
DTC Troubleshooting (cont’d)
A
07XAZ-SZ30100
07SAZ-TB4011A
A
B
Open or Increased Resistance in
Driver’s Seat Belt Buckle Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s seat belt buckle tensioner
4P connector from the floor wire harness (A).
5. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the floor
wire harness 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Open or increased resistance in the driver’s
seat belt buckle tensioner; replace the driver’s seat
belt buckle.
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect both side airbag 2P connectors (A) and
the front passenger’s seat belt buckle tensioner 4P
connector (B).
Does the SRS indicator stay on?
Is DT C 21-1 indicated?
05/06/27 18:09:19 61S6M040_230_0054
−
01
*01
01
S6M6A00K79100081213FAAT00
−
−
−
−
YES
NO
Special Tools Required
YES
NO
DTC 21-3:
23-55
23-55
B
SRS UNIT CONNECTOR B (18P)
A
07XAZ-SZ30100
07SAZ-TB4011A
11. Disconnect SRS unit connector B (18P) from the
SRS unit. Do not disconnect the simulator lead
from the floor wire harness.
12. Check resistance between the No. 1 and No. 10
terminals of SRS unit connector B (18P). There
should be 2.0
3.0
.
Faulty SRS unit or poor cnnection at SRS
unit connector B (18P) and the SRS unit. Check the
connection; if the connection is OK, replace the
SRS unit (see page 23-141).
Open or increased resistance in the floor wire
harness; replace the floor wire harness.
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s seat belt buckle tensioner
4P connector from the floor wire harness 4P
connector (A).
5. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the floor
wire harness 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
(cont’d)
Short to Another Wire or
Decreased Resistance in Driver’s Seat Belt
Buckle Tensioner
Wire side of female terminals
Is the r esistance as specif ied?
Does the SRS indicator stay on?
05/06/27 18:09:20 61S6M040_230_0055
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст